Search results

Hi, I passed through the SSD's using the official tutorial. Here is the VM configs: I am getting the following error when try to enable Trim: Error: Traceback (most recent call last): File "/usr/local/lib/python3.9/site-packages/middlewared/job.py", line 355, in run await self.future...

that's awesome...did you not make any notes step by step???

Hi, were you able to solve it?

changed as suggested...will test and report back pveversion -v proxmox-ve: 8.1.0 (running kernel: 6.5.11-8-pve) pve-manager: 8.1.4 (running version: 8.1.4/ec5affc9e41f1d79) proxmox-kernel-helper: 8.1.0 proxmox-kernel-6.5: 6.5.11-8 proxmox-kernel-6.5.11-8-pve-signed: 6.5.11-8...

??

dmesg | grep -e DMAR -e IOMMU [ 0.000000] Warning: PCIe ACS overrides enabled; This may allow non-IOMMU protected peer-to-peer DMA [ 0.008105] ACPI: DMAR 0x00000000C3C0D000 0000C8 (v01 INTEL CFL 00000002 01000013) [ 0.008144] ACPI: Reserving DMAR table memory at [mem...

ok, some progression! stuck at this now... Here is my grub: GRUB_CMDLINE_LINUX_DEFAULT="quiet intel_iommu=on iommu=pt pcie_acs_override=downstream,multifunction initcall_blacklist=sysfb_init video=simplefb:off video=vesafb:off video=efifb:off video=vesa:off disable_vga=1...

VM info: other info here: dmesg | grep -e DMAR -e IOMMU [ 0.000000] Warning: PCIe ACS overrides enabled; This may allow non-IOMMU protected peer-to-peer DMA [ 0.008036] ACPI: DMAR 0x00000000C3C0D000 0000C8 (v01 INTEL CFL 00000002 01000013) [ 0.008075] ACPI: Reserving DMAR...

write I am getting the following error (console is not fully showing it but its i915 error??

Thank you! If wasn't enabled in the BIOS... Had to disable all the HP junk like sure start etc.

Hi, I have the following iGPU: lspci -s 00:02.0 -vvvv 00:02.0 VGA compatible controller: Intel Corporation CoffeeLake-S GT2 [UHD Graphics 630] (prog-if 00 [VGA controller]) DeviceName: Onboard IGD Subsystem: Hewlett-Packard Company CoffeeLake-S GT2 [UHD Graphics 630]...

It's not shown there:

Hi, I have the following two NVME's: lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS nvme1n1 259:0 0 931.5G 0 disk ├─nvme1n1p1 259:1 0 1007K 0 part ├─nvme1n1p2 259:2 0 1G 0 part /boot/efi...

bump, any one?

Hi, I am thinking to add 2 mini pc nodes with dual NICs and create my first ever proxmox cluster. I am already running pfSense on my single node. to do HA on pfSense, you need a sync interface. This would mean that I need 3 network interfaces: WAN, LAN and Sync Since I have only 2 NICs...

I had problems with setting up the MTU of 9000. I enabled the jumbo frames on my Cisco switch and then pinged it using the following: ping -s 8184 192.168.10.254 (-s is to specify the size of the data packaget to be sent) the response shows that it can only carry the data packets of size 8192...

does this mean I could setup 16 for the following VM:

This makes sense. I will try to pass 1 x NIC (enp68s0f0) port to the VM instead of creating a bond and see if that makes a difference. Thanks very much for your help

is this how you set it up?

Hi, I have a 10Gig card with 2 NICs I created the Linux Bond using these 2 NICs and then created a Linux bridge on top of this bond as shown below: I am using this bond0 as a LAN in pfSense by creating the Linux Bridge (vmbr1). pfSense recognises this interface (vmbr1) as 10 gig as shown...