Search results

Die "routers" Option in host-spezifisch festzulegen ist etwas ungewöhnlich. Würde es mal mit einer einfacheren Konfiguration versuchen und dann ggf. schrittweise anpassen, weiters ist nicht ganz klar wofür die Option subnet-mask /32 dient, das würde ja bedeuten, dass keine Andere IP Adresse über...

* Check the IP connection (i.e. try pinging the NFS Server) from Proxmox host * If it's working: try to add a "manual" share in addition to storage definition, i.e. run e.g. mount.nfs ftpback-rbx4-118.ovh.net:/sharename /mnt/tempshare If this works but the Proxmoxstorage still not there is a...

No - "turnkey-core" is only one kind of Debian template. You can create your own one easily by running "Convert to template" on an existing container which has installed all packages you need.

Run apt install isc-dhcp-client and the problem will not occur any more during the next reboot.

Does this mean the hostname is correct but there is no hostname at all in the DHCP request? If so it's a problem of the container (and not any of Proxmox as such). Which template exactly did you use for creating the container?

Quite clear - in a normal case you can have only one default route. If you want to have routing depending on source address (as you want to do it by specifying "-I") it is necessary to configure different routing tables (in the container). How to do so is explained here...

The filesystem where /var/lib/vz is located (probably root, but depends on you configuration) is probably corrupt and therefore mounted read-only. Assuming it's the root-filesystem: boot the estem with a live-media and verify/repair the respective file-system.

Create at a server with sufficient free disk space ( ~ 10GB) a mirror of proxmox repo. For this install there apt install apt-mirror adapt the configuration files accordingly - see man page man apt-mirror

Assuming you man "ping -I" (instead of "ping -S") : I sets the source address to that value, but does not necessarily mean that the assigned interface is uses. The interface is always selected by the routing table based on destination IP. That means: always the same interface is used in the...

The hostname has to be configured in WEB GUI by Container Configuration -> 'DNS' -> 'Hostname'

In such a case investigate the current boot device (whether boot directory can be read), this can be done in grub rescue mode itself (see https://www.gnu.org/software/grub/manual/grub/html_node/Command_002dline-and-menu-entry-commands.html ) or by booting with a (preferably Linux) live media.

Yes, it is as you have observed - active key and server-id will be available only after installation. Usually there no big difference between pve-no-.subscription and enterprise packages.

The above is not a netmask.

Nicht unbedingt - siehe https://www.ipsidixit.net/2010/03/24/239/

Check via iscsiadm -m session if a connection to the server exists.

Softraid via mdadm möglichst nicht verwenden in Proxmox. Dafür wird ZFS empfohlen.

It is strongly recommended to have a network used exclusively for corosync cluster (and another one for ceph).

Da ist /etc/lvm/lvm.conf anzupassen (definiert welche Disks als PV zulässig sind) die Syntax ist in dieser Datei erklärt, einfach nach "global_filter" suchen.

Die beiden Netzwerke (d.h. das vom Provider und das virtuelle mit den VMs) müssten über eine Bridge verbunden sein. Geht aber nur, wenn der Provider die MAC-Adressen der virtuellen NICs in den VMs zulässt (AFAIK ist das eher nicht er Fall, aber mit dem Provider klären). Um ein lokas ipv6 Netz zu...

NAS connected with just 1Gb/s network I would use in a productive environment only as backup-server. To have local disks would be always faster and more reliable; for home-usage it may also work fine with 1Gb/s network, depending on the amount of data, at least Promox supports it. However, if...