Recent content by tlex

in my case, I got stuck a 3% for 10 minutes and then the installation resumed. 02:00.0 Non-Volatile memory controller [0108]: Micron/Crucial Technology P2 NVMe PCIe SSD [c0a9:540a] (rev 01) Subsystem: Micron/Crucial Technology P2 [Nick P2] / P3 / P3 Plus NVMe PCIe SSD (DRAM-less)...

Not super confortable with linux yet, I have an issue mounting my 4tb thunderbolt nvme ssd. I have the device authorized and seen but the only way I can mount it is via fstab and only after a reboot. If I unmount it after that, I can't remount it until a reboot. not very useful for an external...

same issue here.

Well this is fine, The name will change once the container initialize the module. This is why you have : usb0: host=1a6e:089a,usb4=1 # coral ID pre-load // replace USB4 with selection usb1: host=18d1:9302,usb4=1 # coral ID post-load // replace USB4 with selection

Finally got it working. So the issue was to sign the the dkms module. If you're on the same boat (secure boot) and want to stay that way: * Validate that you use secure boot: mokutil --sb-state SecureBoot enabled as root : 1) generate cert: openssl req -new -x509 -nodes -days 36500 -subj...

I have nothing under /dev related to apex. No error messages at boot, but : :~# modprobe gasket modprobe: ERROR: could not insert 'gasket': Key was rejected by service

I tried both with KyleGospo on 6.8.4.3 and the google version on 6.5.13-5 with the same result (apex device not showing up but no visible error message). Is it possible this is related to using dkms and secureboot ? I'm definitely not familiar with secureboot and this is the first proxmox...

My Coral tpu is the M.2 version.

Running Proxmox 8.2.2 here I followed the instructions from this thread and reverted to kernel 6.5.13-5-pve but still a no show. Any idea what I've done wrong ? uname -r 6.5.13-5-pve Steps I've done : apt remove gasket-dkms apt install dkms lsb-release sudo git dh-dkms devscripts pve-headers...

I tried to add "options zfs zil_nocacheflush=1" to a new host I just built but the option doesn't seem to become enable after a reboot. Any Idea ? The hole system is on zfs (3 x 4tb ssd) # cat /etc/modprobe.d/zfs.conf options zfs zfs_arc_max=10096738304 options zfs zil_nocacheflush=1 reboot #...

Taught this could help others as I found it difficult to setup ! I've been using the typical "Proxmox / LXC / Docker / Codeproject" with Coral TPU usb passthough setup but it's been unreliable (at least for me) and the boot process is pretty long. Not super usefull when used with blueiris for...

Well, in the config I tested it’s between the proxmox host and the switch nothing else in between. pc to pc = ok pc to switch = ok Proxmox host to switch (large mtu) = no go pc to switch to proxmox (large mtu) = no go I can ping from the switch but the cli doesn't seem to allow changing packet...

So I have this "issue" I can't figure. I'm trying to enable jumbo frame on my "small" homelab. My proxmox server has a 4 port Realtek 8125B 2.5GBps card. My lan port (enp8s0) is connected to my main switch Tplink TL-SG3210XHP-M2. Jumbo frame is set at 9000 everywhere and the network cable...

I know there is a bug at this time with snmp but I was wondering if there was a workaround or a way to patch this temporarly in order to avoid floodind syslog ? https://bugs.launchpad.net/ubuntu/+source/net-snmp/+bug/2056257 pveversion pve-manager/8.2.2/9355359cd7afbae4 (running kernel...

You're right, I forgot to mention : pveversion pve-manager/8.0.9/fd1a0ae1b385cdcd (running kernel: 6.2.16-19-pve)