Recent content by thefuzz4

Ok cool I'll give that a shot. Thanks.

Hey Everyone, So when I initially installed my proxmox I apparently made the root disk a little small at around 6GB. I'm looking to upgrade it to 7 and I see that it says to have a min of 4GB of free space. I have 3GB of free right now. I'm trying to squeeze another 1GB out but I'm not sure...

Good Morning Oguz, No changes to anything. I just noticed it yesterday. I can't see any other problems with the GUI everything else seems to be working correctly. Output of pveversion -v pveversion -v proxmox-ve: 6.4-1 (running kernel: 5.4.114-1-pve) pve-manager: 6.4-7 (running version...

Trying to create a new VM on my host and the Node screen shows up like this and when I click the drop down there is nothing in there. This isn't part of a cluster its a standalone Home server so not sure whats going on here with why nothing shows up here. I only have 1 VM on this host and that...

Yeah I have everything disabled in the advanced settings for this as well. I followed the guide from netgate about setting up pfsense on proxmox.

CPU: 12 x Intel(R) Core(TM) i7-3930K CPU @ 3.20GHz (1 Socket) NIC: 00:19.0 Ethernet controller: Intel Corporation 82579LM Gigabit Network Connection (rev 06) HDD Raid 1 software level I'm doing the speed test using the speedtest-cli. On the side I'll have to spin up a VM and assign it the new...

Yeah I'm running it directly on the PFSense CLI as well as on the debian host itself. Figure that would provide the least latency results.

No problem at all @jlebherz The VM is running PFSense v2.4.5-release-1 Network is vtnet0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=c00b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,VLAN_HWTSO,LINKSTATE> ether c6:95:59:e2:3d:77 hwaddr c6:95:59:e2:3d:77...

Ok after following that guide I now have the network setup to go through that route. So yay however I'm still only seeing 270.25Mb on the speedtest on the VM where the host is flying at 900+. Just trying to get the speeds to be somewhat the same.

So I have my proxmox host running with its VMs which get their access to the internet through the pfsense VM. The VM uses MAC address cloning to get its IP address from Hetzner since I bought a 2nd IP from them. On the Proxmox host itself the internet screams but on the PFSense VM it just...

Problem solved it was all related to me using the Hetzner firewall. I've disabled the firewall on both of my hosts and all is right in the world.

Turns out that issue #2 listed above was because of the fact that I'm using the Hetzner firewall. I intend to remove this once I have things working the way I want. So now to figure out why DHCP requests do not work.

Continuing with my progress. I setup the hack to set the mtu to 1400 on the virtio interface. I understand I'll have to probably redo this after any updates. Problems that are left: 1. Guests on host #2 will not pull an IP from the PFSense VM on host #1. If I set a static IP then it works...

Well so the good news is that I now have my servers communicating over the vlan YES!!!!. But here is the bad news. The VMs cannot talk to each other over the vlan. Just so I'm clear on something with VLANs. Should the VMs be on the same vlan that the bridge is on? Thanks for your help...

Ok so the good news is that I managed to finally get the hosts to talk to each other over the VSwitch by adding the Private IP as the destination in Hetzner firewall. Phew that bit is good. Now I'm trying to figure out how to get the VMs on the hosts to be able to talk to each other.