Recent content by Pegasus

I didn't make any changes to the Postgresql config. I just installed PMG into a base Debian LXC container.

1) I looked up files filling up the pg_wal directory and pending replication is the most common reason, so I assumed PMG used it for the cluster replication. 2) These files are slowly consuming all available disk space. I'm at 81% full as of now and the pg_wal directory is currently 4.1GB, 64%...

Hello. When I set up PMG, I intended to add a second node so I created a cluster. I haven't been able to add that node yet and won't have time to do so in the near future. I see in other posts manual instructions for removing the cluster but will that automatically adjust the PostgreSQL config...

Hello. I've been running PMG for awhile (currently on v8.1.8) and it's been working well until about 6 months ago when I can no longer get mail from certain places like LuxSci, PayPal or Synchrony Bank. For any of these, the log shows: 2025-02-26T20:15:34.771123-05:00 smaRTmail1b...

Hello. In order to reduce attack surface and disk space requirements, I like to build my Linux systems from the absolute minimum. To that end, is Proxmox willing to create a base Debian template that has literally nothing installed but the base system? I.e. select nothing in tasksel when asked...

No, I guess I glossed over your reply thinking there were still problems mentioned at the end of it. Plus, I was hesitant to remove everything afraid it will mess something else up, since I don't know everything 'pvecm updatecerts' does. I will try your "clean slate" steps next time though...

Thanks to some folks in the IRC channel, I finally fixed this (at least partially: the remote Web console works again) by doing the following on the node whose Web page I'm connected to: ssh -o HostKeyAlias=IPv4.address.of.other.node IPv4.address.of.other.node ssh -o...

I just tried fixing this again and now even if I use an IPv6 address in the vncproxy command, /usr/bin/ssh -e none -T -o BatchMode=yes IP:V6:address:of:other:node /usr/sbin/qm vncproxy $VMID the connection from the command line succeeds. (I see RFB 003.008.) I also tried the command using the...

Hello. I too am running into the original problem posted in this thread, specifically I'm getting Host key verification failed. when testing using the vncproxy command given above, yet I can ssh between the nodes using their host names and get details of the remote node and the VMs on it via...

Is DRBD9 still considered a technology preview since your last comment, @fabian?

I'm in a similar spot here... 5 node cluster with two pairs of DRBD8 nodes with no viable path to upgrade to ProxMox 4.x with comparable performance and redundancy. I second offering DRBD8 kernel module either in the kernel or as a package. EDIT: It seems DRBD 8 can be upgraded to DRBD 9...

Technically, yes, but drbdmanage assumes that your VG is called "drbdpool". You can change that in /etc/drbdmanaged.cfg though https://www.drbd.org/en/doc/users-guide-90/ch-admin-drbdmanage

That's correct. DRBD9 just allows for more than two replicated storage nodes but works fine with just two as well.

It's not so much that it's unclear, it's just not as easy to tell at a quick glance because the contrast between background and input field is reduced or eliminated. (I have this complaint with all flat style GUIs, not just Proxmox.) Take the logon modal for example. In 3.x, the input fields are...

Is there any way to change the layout of the Web GUI back to the v3.x style with tabs across the top? I'm sure the new v4.x layout is nice for mobile devices but on desktop-size screens, it's just annoying since I have to scroll vertically when I have plenty of horizontal space that was quicker...