Recent content by Oanh

I haven't booted this in quite a while. When I attempted to boot it last night I was presented with some pretty scary screens. Here are a couple of screenshots. It will boot into proxmox but as soon as I attempt to start a VM I am presented with these errors. Any help would be greatly...

Just a bump on this thread. I'm sure it's simple, I'm just too ignorant to figure it out. https://forum.proxmox.com/threads/need-to-remove-sdg-cannot-boot-pve.103093/ Thx

I recently attempted to add an SSD to my VM via PVE and now Proxmox will not boot. Attached are screenshots. I think the drive is sdg. Initially I tried to mount it in PVE through the shell and it looks as though I added it as a scsi device. I couldn't get the drive to show up in my vm, so I...

I had someone setup Proxmox and when they did, they ran a Linux command to see what ID the wired ethernet was using. Then they ran a Linux command to change that ID (as Proxmox was trying to use the WiFi ethernet address) I am no longer in contact with that individual and need to know how to...

Run this command ls -l /dev/disk/by-id Do not use ls -lah /dev/disk/by-id Then simply find your new (replaced) drive letter (in my example it was sdc) So disk/by-id (for me) was: ata-WDC_WD80EZAZ-11TDBA0_7SJR8P1U So I used this command: zpool replace pool1 1200958216758885009...

Thx Didn't know I had to reboot Upon rebooting, I get the following Not too concerning (except for the 2.78V one with the ALARM) Ran it a few times while under load and all the other values changed slightly, but I am just concerned with the 2.78V reading Thoughts...? it8792-isa-0a60 Adapter...

I did what you requested root@myserver:~# sensors-detect # sensors-detect revision $Revision$ # System: Gigabyte Technology Co., Ltd. X570 AORUS PRO WIFI [-CF] # Kernel: 5.4.24-1-pve x86_64 # Processor: AMD Ryzen 9 3900X 12-Core Processor (23/113/0) This program will help you determine which...

I think I did that already I am not in front of the computer right now Can you give me the shell commands here now and I will try when I get home? Thx

I am running Proxmox 6.1 (kernel 5.4) with netdata and running 2 VM (Win10 and Catalina) Here are my components: Gigabyte X570 Pro Wi-Fi Ryzen 3900X Noctua NH-15S 64GB Hyperx 3000Mhz CL15 (16 x 4) EVGA Supernova 1000 G3 Gold Power Supply WD Blue 1TB SSD (x4) WD HDD 8TB x 2 Gigabyte 2070 Super...

This was the output for the disk-id: lrwxrwxrwx 1 root root 9 Apr 29 10:10 ata-WDC_WD80EMAZ-00M9AA0_VAGDUWBL -> ../../sdb lrwxrwxrwx 1 root root 10 Apr 29 10:10 ata-WDC_WD80EMAZ-00M9AA0_VAGDUWBL-part1 -> ../../sdb1 lrwxrwxrwx 1 root root 10 Apr 29 10:10 ata-WDC_WD80EMAZ-00M9AA0_VAGDUWBL-part9...

Thank you for your offer. I may take you up on it if I run into any difficulties. I should receive the new drive in 2-3 days. Will keep you posted.

Thanks again. I am a total newb when it comes to Linux, so thanks for explaining it simply

Ah, ok I think I understand. The <new disk> is actually the serial number. 2 questions 1) What is the easiest way to get the <new disk> info 2) Which method would you reccomend?

Please bear with me as someone else setup my machine and I am trying to do these changes myself :( : I had two 8TB drives mirrored as "pool1" NAME STATE READ WRITE CKSUM pool1 ONLINE 0 0 0 mirror-0 ONLINE 0 0 0 ata-WDC_WD80EMAZ-00M9AA0_VAGDUWBL ONLINE 0 0 0 ata-WDC_WD80EMAZ-00M9AA0_VAGLGALL...

Thanks for the reply I noticed that ARES is listed on the page you referenced as noted in the attached screenshot. I just need it to shut the computer off when the power goes out and I think this should do it...? https://networkupstools.org/docs/man/genericups.html UPS Type=19 Fideltronic Ares...