Recent content by koalillo

(Well, I completed the boot loader steps because I feared a reboot or a failure of the remaining drive could have been fatal.)

Hi, I followed the "changing a failed bootable device" procedure. I did this because smartd started warning me daily about 24 offline uncorrectable sectors (and then went down to 16). While the resilver, I saw some failures on the *new* drive: # zpool status -v rpool pool: rpool state: ONLINE...

So actually a way to reproduce the distrobox/toolbox error is: [alex@ws ~]$ podman run -d --mount type=devpts,destination=/dev/pts --userns keep-id --volume /dev:/dev:rslave registry.access.redhat.com/ubi9/ubi:latest sleep infinity...

Ugh, I think my "reproduction" is not valid. podman exec -t fails with: Error: crun: chown `/dev/pts/4`: Operation not permitted: OCI permission denied while toolbox/distrobox fail with: open /dev/pts/4: No such file or directory: OCI runtime attempted to invoke a command that was not found

Hi, Thanks to a few Reddit threads, I got rootless Podman to work inside an LXC container. However, my intention was to use distrobox/toolbox, and it doesn't work. I've documented everything in detail here: https://github.com/alexpdp7/alexpdp7/issues/10 ; the gist is that these tools create...

Sure? Because in places like https://pve.proxmox.com/pve-docs/pve-admin-guide.html#pct_configuration : Also, the web console is multiuser- you're probably going to have the same concurrency issues whether someone is editing the files or not. ctrl+f for domains.cfg on that page also finds some...

I've been editing /etc/pve/lxc/vmid.conf files manually so far, because as far as I know, you cannot set lxc.idmap entries automatedly (is that right?). That seems to work as I expect, requires restarting the container to apply, etc. Now I'm automating more of my config, and I was thinking of...

Sorry, no, not really. I got my new server, but it's sitting idle costing me money :) I suspect I might push this down the road. I wanted to do this before moving in any service there, so if I mess up with things, the downtime doesn't matter... but I'm beginning to think I'll skip IPv6 in this...

To clarify, I'd like for hosts (LXC/VMs) to live both in an internal IPv4 network, with masquerading/NAT to access IPv4 Internet, and to get an IPv6 address from the range that my hosting provider gives me (a /64), so they are on the public IPv6 Internet. Ideally, this should continue with my...

https://pve.proxmox.com/wiki/Network_Configuration#sysadmin_network_masquerading I'm currently using this setup because my hosting provider gives me a single IPv4 address, so I have to set up masquerading. I'm setting up a new Proxmox host, and I'm considering adding IPv6 configuration from...

Opened https://bugzilla.proxmox.com/show_bug.cgi?id=4385 .

As this shows high on Google... I was following https://openzfs.github.io/openzfs-docs/Performance and Tuning/Hardware.html#nvme-low-level-formatting , and decided to reformat as 4k... then the Proxmox installer said that booting off 4k-formatted NVMe with ZFS was not supported. Undoing that now :)

BTW, if anyone stumbles into this by Googling, Proxmox 7.3 comes with EL9 templates (Alma, Rocky, and CentOS Stream).

Could we get as a feature doing the nvme formatting to 4096 blocks if needed following: https://openzfs.github.io/openzfs-docs/Performance and Tuning/Hardware.html#nvme-low-level-formatting , it seems that automatically detecting the optimal block size and reformatting before installing is...

Bump...? I think uptake of EL9 clones is being slow, but really, as Proxmox 7 does not support EL7, I was waiting until I could migrate to EL9 before migrating to Proxmox 7. But Proxmox 6 is already out of support. I assume I could make a template work, but...