Recent content by kavejo

  1. K

    Selective smarthost (based on recipient, say outlook.com or live.com)

    +1 Outbound conditional relay (with authentication) would be something I’d be interested too. Ideally based on sender or recipient domain.
  2. K

    Best configuration for a cluster-wide virtual switch

    Just emailed you on the back of the automated Proxmox forum email that notified me of your response :)
  3. K

    How to download LXC version of OpenWRT and run it on Proxmox

    Thank you @oguz, Would I need to convert the file from tar.xz to tar.gz? Do I need to observe any specific naming convention in the way I rename the file? Thank you.
  4. K

    Best configuration for a cluster-wide virtual switch

    Hi @spirit, Thank you for the information - it seems very cool that Software Defined Network could be included in Proxmox. Do you know when such feature would be available? Would you require any help with test this feature? If so I would be more than happy to run some tests. Thank you.
  5. K

    How to download LXC version of OpenWRT and run it on Proxmox

    Hi, I am looking to run an OpenWRT container to provide network access to my VMs. I have seen on https://us.images.linuxcontainers.org/ that there is a template built for OpenWRT 19.07. When I run pveam available, the containers at the URL above are not listed but other ones are listed...
  6. K

    Best configuration for a cluster-wide virtual switch

    For posterity, I seem to have resolved the problem by adding the following 2 entities on /etc/netweok/interfaces: auto vxlan0 iface vxlan0 inet manual vxlan-id 2 vxlan_remoteip 192.168.1.** auto vmbr2 iface vmbr2 inet manual bridge_ports vxlan0 bridge_stp off...
  7. K

    Best configuration for a cluster-wide virtual switch

    That didn’t seem to work well for me or, well, I must not have implemented fully. What I want to achieve is basically this: https://ilearnedhowto.wordpress.com/2016/09/16/how-to-create-a-overlay-network-using-open-vswitch-in-order-to-connect-lxc-containers/. Any suggestion on the best (modern)...
  8. K

    EDAC-Utils shows incomplete information in Proxmox 6.1

    Hi @cromatn5, I have just tested with both kernel 5.0 and 5.3 and I can see that edac-utils misses the per-module information. Seems like this did not happen with 4.* kernel which I could only test with Debian 10 and Ubuntu Live. Comparing lspci between kernel 5.0 and 5.3 this led to no...
  9. K

    Best configuration for a cluster-wide virtual switch

    Good morning all, Browsing the forum I found this article https://forum.proxmox.com/threads/proxmox-vm-lan-between-nodes.63049/. I am wondering if the same configuration could be applied to my set-up. I could set eno4.100 (last interface, VLAN 100) on both nodes and set the switch to only...
  10. K

    Best configuration for a cluster-wide virtual switch

    Hi @102020, Please let me share here the details. This setup consists of 2 equally spec’d servers, both DL380e Gen.8 and each have 4 NICS. The network setup is the same on both boxes and all 4 NICs, for each server, are connected to the same physical switch (192.168.1.253) which provides...
  11. K

    Best configuration for a cluster-wide virtual switch

    Thank you @102020 for your reply. My question is more on "how do I do so?". I am familiar with the steps required to create a Distributed vSwitch in VMware but I am finding it user unfriendly to achieve in Proxmox VE. I mean, assuming I reserve eno4 for vmbr2 for this purpose, how can I ensure...
  12. K

    Best configuration for a cluster-wide virtual switch

    Hi, I have recently set-up a Proxmox VE cluster with 2 HPE DL380e Gen. 8. I’m now looking at the best way to have a segmented virtual network that could span the cluster nodes, so to ensure VMs on the same LAN can communicate to each other regardless of the host where they reside. I have...
  13. K

    EDAC-Utils shows incomplete information in Proxmox 6.1

    Hi @cromatn5, I can't see the skl_uncore driver in my case and unfortunately I don't have a pre 5.3 output of lspci -v. Is there any way - I am new to Proxmox - to install the 5.0 or preceding kernel to test for comparison? Thanks!
  14. K

    EDAC-Utils shows incomplete information in Proxmox 6.1

    Hi @cromatn5, I did have a look at your post however I am not seeing the rationale behind your cron script. Perhaps I am missing some details - and that is why I have not tried it yet. Would yo be so kind to share the thought process behind what the script does, so I can validate if that same...
  15. K

    EDAC-Utils shows incomplete information in Proxmox 6.1

    Just adding an additional information. This seems to be specific to the 5.3 kernel. I have tried to boot Ubuntu LTS with 4.* kernel and the edac-utils show all the information, with the latest Ubuntu release (kernel 5.3) these are missing.

About

The Proxmox community has been around for many years and offers help and support for Proxmox VE, Proxmox Backup Server, and Proxmox Mail Gateway.
We think our community is one of the best thanks to people like you!

Get your subscription!

The Proxmox team works very hard to make sure you are running the best software and getting stable updates and security enhancements, as well as quick enterprise support. Tens of thousands of happy customers have a Proxmox subscription. Get yours easily in our online shop.

Buy now!