Recent content by Jae Lee

anyone have any experience with ATTO FC-81EN fiber adapter card for proxmox? i know this card is supported by VMWare and Hyper-V but do not know for proxmox. Anyone have any experience with getting this card working on proxmox? if not, i might have to just run this on VMWare which I honestly do...

proxmox's kvm livesnapshots still seem to take a lot slower than Xen/vmware snapshots. it takes about a minute, where as in xen usually is max 5-10 seconds.

Doesn't LVM support snapshotting too? What is the difference between it and zfs in terms of snapshots?

Thanks for the replies. FYI, I am mainly doing openvz containers. I guess this is why I am confused because only KVM supports the live snapshots. Is it safe to assume that due to the nature of openvz, live snapshots are not possible (ram state)? If so, i'm curious to see how Xen handle this...

i still cant figure out if i'm doing it wrong or if this is some kind of limitation of proxmox. on xen/vmware, i simply right click on vm -> take snapshot, and within seconds i have a backup i can revert back to or clone off of at any time. on proxmox, when i create snapshot, the bigger the vm...

Hi Dietmar, thank you for your reply. I did unmount it, but not sure how to delete it. Vzdump is not running and it looks like a leftover.

Unfortunately I can't seem to do any on proxmox right now. I tried creating new vm, editing note, it just gets connection timeout. I can't create backup right now it seems. As for hard drives, they were WD RED NAS. I think what I'll do is just re-install the entire server. Fortunately I had...

So let me try clarify this, I really appreciate the help btw. 1) Proxmox was installed on the WD3TB (non-ssd) through latest ISO installer. Proxmox by default installs using ext3? Other VMs I created are using ext4. 2) All the drives are configured as AHCI. No RAID was used. Now if all comes...

i have not done RAID or even soft raid. just 4 hard disks set to JBOD (just a bunch of disks).

Here is the cat /proc/mounts: root@server1:~# cat /proc/mounts sysfs /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0 proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0 udev /dev devtmpfs rw,relatime,size=10240k,nr_inodes=33012938,mode=755 0 0 devpts /dev/pts devpts...

So heres my pveperf: root@server1:~# pveperf CPU BOGOMIPS: 166389.92 REGEX/SECOND: 546091 HD SIZE: 94.49 GB (/dev/mapper/pve-root) BUFFERED READS: 30.60 MB/sec AVERAGE SEEK TIME: 13.67 ms FSYNCS/SECOND: 106.28 DNS EXT: 88.38 ms DNS INT: 121.63 ms...

The /dev/sda is proxmox. It was a stock installation off the latest proxmox iso. But I do see the various /dev/mapper/pve-root and /dev/mapper/pve-root, etc which are from /dev/sda. Is there a probblem? This is how it looks atm: root@server1:~# df -h Filesystem...

Host is /dev/sda, VM is on /dev/sdb: root@server1:~# fdisk -lu /dev/sda WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 3000.6 GB, 3000592982016 bytes 255 heads, 63 sectors/track, 364801 cylinders, total...

Btw, I was running Docker inside the KVM. Could this have anything to with it?

I do not have RAID by software, it is just JBOD. And FYI, smartctl checks out fine across all my hard drives, all test scans PASSED. I basically did: smartctl -d ata -H /dev/sdb But so here is one interesting thing I found. First, I have: WD3TB #1 (proxmox) WD3TB #2 (extra) IntelSSD480 #1...