Recent content by Deli Veli

Ran below root@pmox1:~# memtester 1024 5 Here is the results root@pmox1:~# memtester 1024 5 memtester version 4.3.0 (64-bit) Copyright (C) 2001-2012 Charles Cazabon. Licensed under the GNU General Public License version 2 (only). pagesize is 4096 pagesizemask is 0xfffffffffffff000 want...

Ok got another crash today with unable to handle kernel paging on the same server. Below is the stack trace Mar 26 19:53:22 pmox2 pvestatd[1543]: command '/sbin/lvs --separator : --noheadings --units b --unbuffered --nosuffix --options vg_name,lv_name,lv_size,lv_attr,po...

Hi @Chris thank you for your response. I had issues with the previous kernel but don't have the exact version of the kernel. Not sure if the issue was identical either. No, I have not tried to reproduce this issue on the previous kernels. I can give it a shot if you could tell me which kernel...

With latest Proxmox 5.3-1 I am running into a Bug that halts KVMs. It is running on Intel NUC 8. Below is the syslog and pve info. Mar 26 00:21:09 pmox2 kernel: [630425.268008] BUG: unable to handle kernel paging request at ffffffffc17edb60 Mar 26 00:21:09 pmox2 kernel: [630425.268452] IP...

Simple LVM addition through the gui is simple and I had done it in the past. It works just fine. However, adding lvm via gui does not give you the option of creating the software raid. As mentioned, software raid is a must. Lets try to find the answer a different way. The goal is to create LVM...

Unfortunately hardware raid is not an option since we use PCI ssds. It has got to be a software raid. High Performance is a must. Gave a shot to zraid but it was extremely slow. LVM raid seems a lot faster. However, ideally what I would like to do is to create the LVM raid and then add this to...

Yes gave a shot to ZFS. Performance decreased drastically. I know that I am missing something very trivial with the Proxmox showing %100 allocated when it is not. Just I am not sure if it is a Proxmox bug or my implementation below is not correct. pvcreate /dev/nvme0n1 /dev/nvme1n1...

Any clue on how to accomplish this? Creating Raid 10 with LVM and have Proxmox not to recognize this as 100% full?

Hi @dcsapak thank you for getting back. I have 4x 1T NVMe ssd. I have to create Raid10 for redundancy. Another goal is to get the best performance from those PCI ssds. How else can I accomplish this without above steps?

Goal: Create 4 drive RAID10 over LVM and add that storage to Proxmox. Problem: When I add raid10 lvm storage, Proxmox gui shows %100 full on the storage && shows ~4T of space instead of respecting raid10 mirrors and show ~2T of space. Creating a mount point and mounting to a folder on root...

@guletz I did not expect Raidz to perform that poorly comparing to single drive is what I meant. Naturally, I was expecting some slow down but not to this extend. If you look at the results, you can see that Zraid1 on NVMe pci ssds performed almost the same as mirrored non-performance ssds over...

Another question. Above solution meaning creating the LVM RAID10 and mounting to a folder in filesystem then using that inside Proxmox does seem to work. However when I add LVM directly on proxmox GUI, it shows 100% of the data taken. Here are the steps for both scenarios. Does NOT work...

Hi @BrandonN so RAID over LVM gives the best performance as it currently stands. Check out the thread above. Might help you out as well.

Ok below are the steps taken to create LVM RAID10 on 4x NVMe SSD drives. Also attaching benchmarking results. // Create Physical Volume Drives pvcreate /dev/nvme0n1 /dev/nvme1n1 /dev/nvme2n1 /dev/nvme3n1 // Create Volume Group vgcreate my_vol_grp /dev/nvme0n1 /dev/nvme1n1 /dev/nvme2n1...

Update on another round of experiment. Destroyed the Raidz-1, not beneficial from performance perspective. Created RAID10 with below commands, zpool create -f -o ashift=12 nvmeraid10pool mirror /dev/nvme0n1 /dev/nvme1n1 mirror /dev/nvme2n1 /dev/nvme3n1 Below is the same benchmark results. It...