bbgeek17's latest activity
-
bbgeek17 replied to the thread Dedicated Proxmox network interface connectivity issue.Hi @AndyKosh , It is impossible to draw any conclusions about the behavior of your network without detailed technical information about your environment. This should include network configuration files, the current state of the systems involved... -
bbgeek17 replied to the thread Atomic rename error.Have you checked the ownership and permissions of the entire path of the offending file? Can you perform same operations in that path? With that file? Have you checked your NAS log files? Can you increase verbosity of the logs on the NAS side...
-
bbgeek17 replied to the thread Delete orphaned VM DIsk.Please provide: cat /etc/pve/storage.cfg pvesm status mount lsblk qm config [id] pvesm list [storage] As requested, provide full unredacted commands that you run: rm, ls, etc Direct and file listing on : vm-9000-disk-1.qcow2 (if that is the disk...
-
bbgeek17 replied to the thread Atomic rename error.The "cp/mv", "ls", "touch" Blockbridge : Ultra low latency all-NVME shared storage for Proxmox - https://www.blockbridge.com/proxmox
-
bbgeek17 replied to the thread [SOLVED] VM Migration issue.You may need to run this command, as suggested by the log. Or manually update these files with new keys. Blockbridge : Ultra low latency all-NVME shared storage for Proxmox - https://www.blockbridge.com/proxmox
-
bbgeek17 replied to the thread Atomic rename error.Based on the Path to the file this particular error seems to come via NFS. Have you examined the file? Try a few operations manually. Blockbridge : Ultra low latency all-NVME shared storage for Proxmox - https://www.blockbridge.com/proxmox
-
bbgeek17 replied to the thread Is a 3-node Full Mesh Setup For Ceph and Corosync Good or Bad.In a Node Down scenario, you are left with two nodes that can still communicate directly with each other, since this is a mesh network. Additional load only becomes a factor in a Link Down scenario. In that case, depending on the topology and...
-
bbgeek17 replied to the thread Snapshot of VM Freezes All Other VMs on Node.It’s possible that you’re experiencing what is commonly referred to as “VM stunning.” In many virtualization environments (ESXi, PVE, etc.) it is most often caused by slow or congested storage. As suggested earlier, try performing the operation...
-
bbgeek17 replied to the thread [SOLVED] where to find proxmox 8.1-2.Thank you for the update @Ishadow , feel free to mark this thread as SOLVED by editing the original post and using the appropriate prefix from the subject dropdown. Blockbridge : Ultra low latency all-NVME shared storage for Proxmox -...
-
bbgeek17 replied to the thread Is a 3-node Full Mesh Setup For Ceph and Corosync Good or Bad.@x509 , welcome to the forum. We don’t use Ceph or mesh networking in our deployments. That said, if you plan to engage a Proxmox Partner, I would recommend following their guidance, they will ultimately be responsible for supporting your...
-
bbgeek17 replied to the thread [SOLVED] where to find proxmox 8.1-2.Hi @Ishadow, welcome to the forum. There are several suggestions in this thread: https://forum.proxmox.com/threads/fujitsu-primergy-tx1320-m3-fujitsu-praid-cp400i.146653/ You also have other options: - Try PVE9 - Try Debian (12 or 13) and...
-
bbgeek17 replied to the thread Snapshot of VM Freezes All Other VMs on Node.It may be helpful for the community if you provide the following: cat /etc/pve/storage.cfg pvesm status lsblk pvs vgs lvs qm list qm config [vm_id_snapshotted] - task output of the snapshot - journalctl output +-1min around snapshot - dmesg...
-
bbgeek17 replied to the thread How to copy NTFS to ZFS.Hi @FrostyIce , welcome to the forum. Technically your question is not related to Proxmox Virtualization Environment at all. You may find experience in r/HomeLab and r/DataHoarder more suitable for your inquiry. Cheers Blockbridge : Ultra low...
-
bbgeek17 replied to the thread Snapshot of VM Freezes All Other VMs on Node.Hi @asummere , welcome to the forum. The answer to your question depends heavily on the overall configuration of your system, most importantly - storage. Can you share more details? Cheers Blockbridge : Ultra low latency all-NVME shared...
-
bbgeek17 replied to the thread Slow upload speed from node to node.You have looping messages that the link goes down and up? That will certainly reset the sessions and slow things down. At a high level it sounds like a hardware issue, perhaps a bug in NIC firmware, or something similar. If this is a one time...
-
bbgeek17 replied to the thread Proposed Hardware Design – Proxmox VE Compatibility & Shortfalls.If you are looking for stable networking you should avoid Broadcom. Ideally, you'd get Mellanox. Blockbridge : Ultra low latency all-NVME shared storage for Proxmox - https://www.blockbridge.com/proxmox
-
bbgeek17 replied to the thread [SOLVED] Validation and questions about iSCSI Config.A quick way to look at the file without all the extensive comments: grep -vE '^\s*(#|$)' /etc/lvm/lvm.conf Blockbridge : Ultra low latency all-NVME shared storage for Proxmox - https://www.blockbridge.com/proxmox
-
bbgeek17 replied to the thread [SOLVED] DR configuration in Proxmox.:-) AI spell check PS although it would be very interesting if PDM allowed 3rd party Plugins similar to Storage subsystem Blockbridge : Ultra low latency all-NVME shared storage for Proxmox - https://www.blockbridge.com/proxmox
-
bbgeek17 replied to the thread [SOLVED] DR configuration in Proxmox.Veeam recovery, to my understanding, can be performed “online,” meaning the VMs become available as soon as the recovery process is initiated. Proxmox Backup Server (PBS) definitely supports this capability. That said, if IP addressing changes...
-
bbgeek17 replied to the thread [SOLVED] Validation and questions about iSCSI Config.So to clarify, the multipath_component_detection is 1 by default. Somehow you ended up setting it to zero, leading to a now logical error. Blockbridge : Ultra low latency all-NVME shared storage for Proxmox - https://www.blockbridge.com/proxmox