bbgeek17's latest activity
-
bbgeek17 replied to the thread Unable to get Virtual Machine on the network. I believe my network setup is incorrect..I'd recommend getting familiar with using CLI and doing it via physical console. Since it's the only IP on your system, any mistake (UI or CLI) will cause access disruption to the system. Just take address and gateway lines and move it under... -
bbgeek17 replied to the thread Help me understand my storage options.Start-to-end? No. You need to perform a subset from CLI. Especially if Multipath is involved. Blockbridge : Ultra low latency all-NVME shared storage for Proxmox - https://www.blockbridge.com/proxmox
-
bbgeek17 replied to the thread Help me understand my storage options.Hi @mhentrich . You can use either iSCSI or FC. The resulting view from PVE perspective is the same. You are correct that you would present LUNs, or single large LUN, to your hosts. You would then use LVM, not LVM-thin. You will be able to use...
-
bbgeek17 replied to the thread Unable to get Virtual Machine on the network. I believe my network setup is incorrect..Welcome to the forum @aztekapride . You need to move the IP address from the bond0.340 to the bridge, and move the bridge to the bond0.340. That is the most common approach. Otherwise, you will need to tag the traffic in VM internally...
-
missing "a" in ShredDir ? To fix the missing iso ? edit: double check your keyboard, If letters are missing or mixing in configuration as in this thread, errors will be excepted.
-
bbgeek17 replied to the thread storgae configuration.You are correct. It is for storage that is suitable to contain ISO images, which are files. The ZFS and LVM (local) storage are raw block devices, they cannot store files. They are not available for this step in the Wizard. I cannot tell how...
-
bbgeek17 replied to the thread storgae configuration.@Impact is right on - you are on ISO selection screen, not disk. Select "Do not use any media" and then Next. You can come back later to add an ISO, if you need one. Blockbridge : Ultra low latency all-NVME shared storage for Proxmox -...
-
bbgeek17 replied to the thread Proxmox 9.1.4 import SUSE VM from ESXi.As I mentioned, I am not a SLES expert. I don't know whether you properly booted into Rescue mode. I am not sure whether the disk of the VM is still there, is it? Perhaps you need to execute a few more commands to make the Rescue mode usable...
-
bbgeek17 replied to the thread Proxmox 9.1.4 import SUSE VM from ESXi.Run "lsblk" from the rescue mode, then replace UUID=uuid within the file with a /dev/sdX type keyword. Or, if you can figure out the new UUID, with that. Blockbridge : Ultra low latency all-NVME shared storage for Proxmox -...
-
bbgeek17 replied to the thread proxmox 8 - how migrate vm without shared storage ?.Have you tried to use PVE CLI yet? qm migrate <vmid> <target> [OPTIONS] qm migrate <vmid> <target> [OPTIONS] Migrate virtual machine. Creates a new migration task. <vmid>: <integer> (100 - 999999999) The...
-
bbgeek17 replied to the thread [SOLVED] local fs full: ghost files edition.The backup was configured to store files in a folder /mnt/usb/dump. It does not know whether that folder is backed by USB, NVMe, or Cloud drive. At some point when the backup was executed the USB was either not present or not recognized. The...
-
bbgeek17 replied to the thread Proxmox 9.1.4 import SUSE VM from ESXi.Can you find out the context of your /etc/fstab ? Blockbridge : Ultra low latency all-NVME shared storage for Proxmox - https://www.blockbridge.com/proxmox
-
bbgeek17 replied to the thread Proxmox 9.1.4 import SUSE VM from ESXi.I meant it just as a test that it boots. If I remember correctly, PVE is not a supported hypervisor from SAP HANA contract perspective. Perhaps it has changed since I last looked? Blockbridge : Ultra low latency all-NVME shared storage for...
-
bbgeek17 replied to the thread [SOLVED] - Can't seem to upgrade....Depends on how one "stumbles" into learning about no-sub repo... Blockbridge : Ultra low latency all-NVME shared storage for Proxmox - https://www.blockbridge.com/proxmox
-
bbgeek17 replied to the thread [SOLVED] - Can't seem to upgrade....Enjoy PVE and see you in a few weeks when you come back with "my GUI stopped working and I did not change anything". This is based on the fact that you: - informed us that you are not an Enterprise subscription user in the now deleted post -...
-
bbgeek17 replied to the thread proxmox 8 - how migrate vm without shared storage ?.I saw "6 pve" and inverted it to "pve 6". Nevermind... it was an interesting side adventure :-/ Blockbridge : Ultra low latency all-NVME shared storage for Proxmox - https://www.blockbridge.com/proxmox
-
bbgeek17 replied to the thread proxmox 8 - how migrate vm without shared storage ?.HEre i His first screenshot in the opening post shows migration from node2 to node6, with LUN92 involved. It is not available to node6 Blockbridge : Ultra low latency all-NVME shared storage for Proxmox - https://www.blockbridge.com/proxmox
-
bbgeek17 replied to the thread storgae configuration.It should have "images" if you want to place VMs there. That is the nomenclature that PVE uses for VM virtual disks. Blockbridge : Ultra low latency all-NVME shared storage for Proxmox - https://www.blockbridge.com/proxmox
-
bbgeek17 replied to the thread proxmox 8 - how migrate vm without shared storage ?.You are running an OLD (unsupported) version of PVE. In fact, as of today Proxmox dropped the repository to support Buster. The code that generated the error you provided is different, improved, in newer versions...
-
bbgeek17 replied to the thread Proxmox 9.1.4 import SUSE VM from ESXi.Hi @jeffgott , welcome to the forum. While I've never had to deal with SUSE on PVE, I'd recommend trying a fresh install Does that work? Blockbridge : Ultra low latency all-NVME shared storage for Proxmox - https://www.blockbridge.com/proxmox
