Dear all,
i installed RHEL6 as a KVM in proxmox and have problems accessing ttys in proxmox' vnc console:
- pressing [Strg]+[Alt]+[F1] : doesn't work
- pressing [Strg]+[Alt]+[F2] : doesn't work
- pressing [Strg]+[Alt]+[F3] : doesn't work
- pressing [Strg]+[Alt]+[F4] : doesn't work
- pressing [Strg]+[Alt]+[F5] : shows either my X Desktop or a tty, depending on my settings
- pressing [Strg]+[Alt]+[F6] : shows either my X Desktop or a tty, depending on my settings
- pressing [Strg]+[Alt]+[F7] : shows either my X Desktop or a tty, depending on my settings
- pressing [Strg]+[Alt]+[F8] : shows either my X Desktop or a tty, depending on my settings
And for F5 - F8 it seems that either all of them show my Desktop or all of them show a tty.
Is this a problem about vnc or do i have errors in my config?
Info: Red Hat replaced sysvinit with upstart
i installed RHEL6 as a KVM in proxmox and have problems accessing ttys in proxmox' vnc console:
- pressing [Strg]+[Alt]+[F1] : doesn't work
- pressing [Strg]+[Alt]+[F2] : doesn't work
- pressing [Strg]+[Alt]+[F3] : doesn't work
- pressing [Strg]+[Alt]+[F4] : doesn't work
- pressing [Strg]+[Alt]+[F5] : shows either my X Desktop or a tty, depending on my settings
- pressing [Strg]+[Alt]+[F6] : shows either my X Desktop or a tty, depending on my settings
- pressing [Strg]+[Alt]+[F7] : shows either my X Desktop or a tty, depending on my settings
- pressing [Strg]+[Alt]+[F8] : shows either my X Desktop or a tty, depending on my settings
And for F5 - F8 it seems that either all of them show my Desktop or all of them show a tty.
Is this a problem about vnc or do i have errors in my config?
Info: Red Hat replaced sysvinit with upstart
Code:
[root@rh60-64bit-test-1 init]# cat /etc/init/start-ttys.conf
#
# This service starts the configured number of gettys.
start on stopped rc RUNLEVEL=[2345]
env ACTIVE_CONSOLES=/dev/tty[1-8]
env X_TTY=/dev/tty8
task
script
. /etc/sysconfig/init
for tty in $(echo $ACTIVE_CONSOLES) ; do
[ "$RUNLEVEL" = "5" -a "$tty" = "$X_TTY" ] && continue
initctl start tty TTY=$tty
done
end script
Code:
[root@rh60-64bit-test-1 init]# cat /etc/sysconfig/init
# color => new RH6.0 bootup
# verbose => old-style bootup
# anything else => new style bootup without ANSI colors or positioning
#BOOTUP=color
BOOTUP=verbose
# column to start "[ OK ]" label in
RES_COL=60
# terminal sequence to move to that column. You could change this
# to something like "tput hpa ${RES_COL}" if your terminal supports it
MOVE_TO_COL="echo -en \\033[${RES_COL}G"
# terminal sequence to set color to a 'success' color (currently: green)
SETCOLOR_SUCCESS="echo -en \\033[0;32m"
# terminal sequence to set color to a 'failure' color (currently: red)
SETCOLOR_FAILURE="echo -en \\033[0;31m"
# terminal sequence to set color to a 'warning' color (currently: yellow)
SETCOLOR_WARNING="echo -en \\033[0;33m"
# terminal sequence to reset to the default color.
SETCOLOR_NORMAL="echo -en \\033[0;39m"
# Set to anything other than 'no' to allow hotkey interactive startup...
PROMPT=yes
# Set to 'yes' to allow probing for devices with swap signatures
AUTOSWAP=no
# What ttys should gettys be started on?
#ACTIVE_CONSOLES=/dev/tty[1-6]
ACTIVE_CONSOLES=/dev/tty[1-8]
# Set to '/sbin/sulogin' to prompt for password on single-user mode
# Set to '/sbin/sushell' otherwise
SINGLE=/sbin/sushell
Last edited: