[SOLVED] Configuration OVS bond + bridge + internal ports

[cmonty14]

Hello,

I try to configure an OVS bond + bridge + internal ports with my new Proxmox VE 7.0 installation.
However, this fails although a follow the example available in relevant wiki page.

This is my current /etc/network/interfaces:

source /etc/network/interfaces.d/*

auto lo
iface lo inet loopback

auto eno1
iface eno1 inet manual
        ovs_mtu 1500
#eno1

auto enp4s0f3
iface enp4s0f3 inet manual
        ovs_mtu 1500
#enp4s0f3

auto bond0
iface bond0 inet manual
        ovs_type OVSBond
        ovs_bridge vmbr0
        ovs_bonds eno1 enp4s0f3
        ovs_options bond_mode=balance-tcp lacp=active other_config:lacp-time=fast
        ovs_mtu 1500
#bond0

auto vmbr0
iface vmbr0 inet manual
        ovs_type OVSBridge
        ovs_ports bond0 vlan10 vlan20 vlan30 vlan90 vlan100
        ovs_options tag=10 vlan_mode=native-untagged trunks=20,30,90,100
        ovs_mtu 1500
#vmbr0

auto vlan10
iface vlan10 inet static
        ovs_type OVSIntPort
        ovs_bridge vmbr0
        ovs_options tag=10
        ovs_mtu 1500
        address 192.168.1.11
        netmask 255.255.255.0
        #post-up ip route add 192.168.1.0/24 via 192.168.1.1 dev vlan10
#LAN

auto vlan20
iface vlan20 inet static
        ovs_type OVSIntPort
        ovs_bridge vmbr0
        ovs_options tag=20
        ovs_mtu 1500
        address 192.168.2.11
        netmask 255.255.255.0
#PVEGST

auto vlan30
iface vlan30 inet static
        ovs_type OVSIntPort
        ovs_bridge vmbr0  
        ovs_options tag=30
        ovs_mtu 1500
        address 192.168.3.11
        netmask 255.255.255.0
#PVEMGRT

auto vlan90
iface vlan90 inet static
        ovs_type OVSIntPort
        ovs_bridge vmbr0
        ovs_options tag=90
        ovs_mtu 1500
        address 192.168.9.11
        netmask 255.255.255.0
#VPN

auto vlan100
iface vlan100 inet static
        ovs_type OVSIntPort
        ovs_bridge vmbr0
        ovs_options tag=100
        ovs_mtu 1500
        address 172.16.10.11
        netmask 255.255.255.0
#DMZ

Please advise why this configuration is not working, means bond0, vmbr0 and all vlans are not getting activated.

THX

 

[cmonty14]

This configuration is working as expected:

source /etc/network/interfaces.d/*

auto lo
iface lo inet loopback

auto eno1
allow-vmbr0 eno1
##eno1

auto enp4s0f3
allow-vmbr0 enp4s0f3
##enp4s0f3

auto bond0
iface bond0 inet manual
        ovs_type OVSBond
        ovs_bridge vmbr0
        ovs_bonds eno1 enp4s0f3
        ovs_options bond_mode=balance-tcp lacp=active other_config:lacp-time=fast
        ovs_mtu 1500
##bond0

auto vmbr0
iface vmbr0 inet manual
        ovs_type OVSBridge
        ovs_ports bond0 vlan20 vlan30
        ovs_mtu 1500
        address 192.168.1.11
        netmask 255.255.255.0
##vmbr0

auto vlan20
iface vlan20 inet static
        ovs_type OVSIntPort
        ovs_bridge vmbr0
        ovs_options tag=20
        ovs_mtu 1500
        address 192.168.2.11
        netmask 255.255.255.0
##PVEGST

auto vlan30
iface vlan30 inet static
        ovs_type OVSIntPort
        ovs_bridge vmbr0
        ovs_options tag=30
        ovs_mtu 1500
        address 192.168.3.11
        netmask 255.255.255.0
##PVEMGRT