Search results

Hi there, Sure, I'd do it for £100. But a word of warning, if you know how to configure proxmox you'll be fine but I really have no clue and I can't get it to work

Thanks for your input - so just to confirm in /etc/network/interfaces add in at any point or in certain areas? Eth0 is my public IP eth1 is my private IP iptables -t nat -A PREROUTING -p tcp -i eth1 --dport 80 -j DNAT --192.168.0.249:80 iptables -A FORWARD -i eth0 -p tcp --dport 80 -j ACCEPT

Anyone have any idea on how to do this?

Hi there, Sure, I'd do it for £100. But a word of warning, if you know how to configure proxmox you'll be fine but I really have no clue and I can't get it to work

Hi I've been playing around with the settings in proxmox for sometime now, and I can't seem to get my public IP to be directly attached to a container on the server. Could someone please post a guide/instructions on how to do this? I've tried bridging a connection to an ethernet port...

I've tried to bond the container to the device, does anyone have a working setup they can post? Or can someone connect my server and help me out? Thanks,

Hmm, so no one has managed to get this setup?

The private ip range does have end point depentant NAT. But I'm sure there must be away I assign the openvm to the ip address 86.8.172.70 but on a different port such as 8080.

Hi there, I've done like you've said the the system is now booting the openvm. But I can't get access to the opvem from the internet or LAN. Should I add back in the route: up route add -host 192.168.0.249 dev vmbr0 here are the logs: Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY...

Here we go. And thanks for your help hopefully with your help this is will start working proxmox:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.249 * 255.255.255.255 UH 0 0 0...

The error is still the same. The openvm won't mount. Here are all the logs to help. Tasks Syslog command finished Abort /usr/sbin/vzctl start 101 Starting container ... Container is mounted Adding IP address(es): 192.168.0.249 RTNETLINK answers: File exists vps-net_add ERROR: Unable to add...

Here is the whole Ifconfig output: proxmox:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:15:c5:e7:17:77 inet6 addr: fe80::215:c5ff:fee7:1777/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:28221 errors:0 dropped:0...

The static IP address which was being used have now changed to 86.8.176.70.

proxmox:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.249 0.0.0.0 255.255.255.255 UH...

I've configured the file you've said, but the VM now cannot start; log error: "synchronized failed to 193.55.167.2 stratum 2" Container is mounted Adding IP address(es): 192.168.0.249 RTNETLINK answers: File exists vps-net_add ERROR: Unable to add route /sbin/ip route add 192.168.0.249 dev...

Anyone able to help me out here? I'm really at a loss right now.

When in the bridge mode I can't seem to get the openvm to get access to the net. I.e even a ping. What should happen is if a static ip hasn't been assigned to a mac code dhpc should take over to provide access until it's been setup with a static assignment. I.e take my router that's set to...

I've just tried the following guilde using shorewall: http://www.montanalinux.org/proxmox-ve-with-shorewall.html But when I come to run shorewall check - I'm getting this error back, and I can't figure out why. I've also tried other ip addresses there too. lanlink:~# shorewall check...

I've got 2 spare ip's (not included that one) which I can use, but they need to be configured by MAC code, to get their static IP. How do I assigned the VM to an IP address? I've restarted the server and did a network restart: lanlink:~# /etc/init.d/networking restart Reconfiguring...

I've made the changes you've suggested but it still doesn't bring me any closer to a solution of access the internet on the container. I've also posted a log on the network restart, just incase you see something thats wrong, that I dont. lanlink:~# /etc/init.d/networking restart...