Search results

So, ive tested it for about 26 hours now, and still no problem. But if i Mount the nfs / samba again, i nearly get the same problem instant. Maybe u have a solution for this? I mounted the samba / nfs like this: (fstab) //censored.your-storagebox.de/backup /mnt/backup cifs...

Hey guys, Actually i just unmounted the Ciffs storage, and until now it wokrs fine (for about 40 minutes now). Maybe only the ciffs storage had an mistake? And Fucked up the whole system? Regards

Hey, here are the content u want to see. Thankyou for your help. Regards zfs list NAME USED AVAIL REFER MOUNTPOINT rpool 11.8G 203G 96K /rpool rpool/ROOT 1.41G 203G 96K /rpool/ROOT rpool/ROOT/pve-1 1.41G 203G...

Hey, yes ssd is enterprise so it shouldnt be the problem i think.. I cant use the implemented transfer feature, cause how i said the storage wont appear after 5 minutes later then boot. Also i dont think that the speed should be the problem, cause still if the speed is rly slow, the storage...

You had read Wrong, its 8x RAM 8192 MB DDR3, so 64gb ram complete. zpool status pool: rpool state: ONLINE scan: none requested config: NAME STATE READ WRITE CKSUM rpool ONLINE 0 0 0 mirror-0 ONLINE 0 0 0...

Intel Core i7-3930 sw raid1 2x Samsung MZ7LM240 ssd sw raid1 2x 3tb hdd (toshiba and seagate) 8x RAM 8192 MB DDR3 System is installed on the ssd raid. So peformance shouldnt be the problem i think. all disk´s passed smart check.

Hey fireon, the problem is static. it Appears 3 to 5 minutes after reboot, and from then the problem is there till i reboot again. pveperf: CPU BOGOMIPS: 76803.12 REGEX/SECOND: 1208377 HD SIZE: 204.41 GB (rpool/ROOT/pve-1) FSYNCS/SECOND: 359.51 DNS EXT: 32.63 ms DNS INT: 48.62 ms...

Hi, i have a problem on an Fresh proxmox installation. I used the complete proxmox image in version: 4.3-10 I used the autoamtical zfs install of proxmox, so zfs is used on all disks. After boot, the Proxmox is fully working for about 3 to 5 Minutes. After that i cant choce an storage. It...

Hey, an nginx reverse proxy will only work for the Webui itself, but you will have problems to use the kvm console after that. So Yes this solution will "work", but it have some critical limitations. regards

Hi, please give some more information. Please provice output of following commands: (U can censor one octet or so in your ip adresses if u want) lspci ip address cat /etc/network/interfaces Pleaso show output of these commands, when your cards are plugged in with an network cable and have...

Hey, i have some trouble setting up my new proxmox with ipv6 subnet. These are my configs: so, now i can ping6 from the host the vmbr0 address: 2a01:4f8:xxx:1270::3 but i cant ping the Guest address: 2a01:4f8:xxx:1270::4 ping6 2a01:4f8:xxx:1270::4 PING...

Ok, so now for one hour 0% packetloss, so the solution is to change the network model to VirtIO. For Linux distribtions this is no problem cuase VirtIO drivers are included. For Windows it might be a problem. Regards

Ok, i Maybe Solved the Problem by myselve. I Just changed the Network Model in Hardware Settings from Intel E1000 to VirtIO. Will update later if my packetl oss is away for a bit longer now.

Hi, I just recognized that i ahve massiv package lost problems with my newly configured proxmox host. PVE version: 4.2-11/2c626aa1 hoster: hetzner Kernel: Linux 4.4.8-1-pve I just setup check_mk for my monitoring and just recognized that i have a fluctuating packet loss of 2 - 35% on my kvm...

Problem is [Solved], i Posted a Working configuration on the top of the Thread

[SOLVED] To setup an Ip subnet with proxmox the host configuration has look like: Host: auto lo iface lo inet loopback # device: eth0 auto eth0 iface eth0 inet static address HOST IP netmask HOST NETMASK gateway HOST Gateway auto vmbr0 iface vmbr0 inet static address (One...