Hello,
It works, the multi path tools are included in the distro (i think you have to install from the repo), if you need i can post my config, we configure as active/active.
Best regards.
Hello, nop, i didn't install yet, is supported by proxmox bare-metal iso install? when i do future upgrades is still working? There is some docs/wiki about the configuration of multipath in proxmox 3?thanks in advance.Max.
Hello, we bought 2 IBM x3550 server (with 2 sas HBA each) connected to IBM v3700 storage, redundant SAS canisters , so we need to setup multipath for the volume to store VMs. There is some documentation to do this in proxmox 3?. Xenserver work out of the box, but proxmox don't.
Thanks in...
Hello.
We are planning to buy a new storage (IBM v3700) with FC HBA in the servers (brocade FC HBA 46M6049) is this card supported by proxmox VE?
thanks in advance.
Best regards.
hello, the drive report no error. Just only one, disk C. But.. when proxmox make a snapshot analyze the guest VM drive? I think not, that happend in the LVM layer, i guess...
Helo:
We recently migrate from proxmox 1 to 2.0.
Buy when the backup starts, at 5 minutes crash the VM and the backup stop. In the same node the backups of linux VM works ok.
any help?
Thanks, best regards.
INFO: starting new backup job: vzdump 102 --remove 0 --mode snapshot --compress lzo...
Hello Tom.
The disk are in hardware raid1 in a ibm server x3250 16 GB RAM. No, the archive is compressed with tar.gz. The server is recovering the backup right now, maybe this is why the fsync/sec value.
Now the server still running the restore (7 hours)
thanks
Regards
the time to restore a 500gb disk is more that 6 hours (still running)
the storage is a NFS storage with SATAII disks and 1gb/s switched network (cisco Switch)
At the begining of the restore process we saw network bursts (60MBytes/s) and then only a few bursts of 4Mbytes/s
the size of the...
Hello.
We need to restore a backup snapshot, but takes too long for de 500 GB VM disk. There is some way to speed up the qmrestore process? I can see the network interface traffic and is not full.
thanks in advance.
Best regards
Hello:
I try to install proxmox ve 1.9 in a HP proliant DL 160 G6, raid controller p410i, raid 1+0 (4 discs 2 tb) 4tb RAID volume and fail when make partitions, any suggestion?
thanks in advance.
Best regards.
Hello:
I have a server with 2 ethernet (2 ips, 2 netid) when I create a master (pveca -c) the master create from IP in the eth0 (wan), i need to change to ip in eth1 (LAN), how can i do this?
thanks in advance
Best regards.
Hello.
the kernel 2.6.32-3-pve. how can i add a target LUN? we recently add 6TB in raid 5 and we want to create a iSCSI target for this /dev/cciss/c0d1: 6001.0 GB, 6001072168960 bytes
any ideas?
thanks in advance.
best regards
Hello:
We have a recently installed proxmox cluster. The master has a 6 TB Raid 5 volume and I wish to share this volume trought iSCSI among the nodes, Is possible to install iscsi target in the master?, i mean, proxmox install custom kernel and the iscsi package and moldules (iscsi_trgt) are...
Re: Error in Perl code: command '/sbin/vgchange -aly storage1' failed with exit code
ahhh OK, I will do that (iSCSI). Thanks for you time!
best regards!
Re: Error in Perl code: command '/sbin/vgchange -aly storage1' failed with exit code
nop, storage 1 is a hardware raid 5 /dev/cciss/c0d1: 6001.0 GB, 6001072168960 bytes . Located in the PVE master. LVM2 VG
Re: Error in Perl code: command '/sbin/vgchange -aly storage1' failed with exit code
Hello.
the error appears when i try to edit the hardware (hardware tab) in a VM located in the nodes (not the master).
when I run vgchange -aly storage1
in the master, I recive
1 logical volume(s) in...
Hello.
I recently install proxmox cluster (latest version). When I enable LVM storage (storage1) shared or not shared, and try to access hardware tab in the nodes recibe
Error in Perl code: command '/sbin/vgchange -aly storage1' failed with exit code 5
if I delete the storage works ok.
the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.