Hi,
I have a strange problem which I am not able to solve.
When I restore vm machine from backup, I can not make network working again. It was not a problem until proxmox 4.x.
If I ping google.com or internal network IP I get around 97% packet loss, few packets in a row are successful then many...
Hi,
I try new proxmox 41 in test environment without hardware watchdogs.
Unforunately, I can not make the failed node restart.
I tried few commands I have found on this forum like
ifconfig vmbr1 down
kill -9 corosync
Any node got disconnected, but it stay turned on. Sometimes I got these...
Hi,
smartd warned me about some problems with my drives I use for ceph and so I have two questions.
1] Is here any special fsck command to check ceph xfs filesystem or I would just use fsck.xfs /dev/sdX ?
2] What is the correct way to replace a drive, particullary not dead yet in my case?
I...
Hi,
now I have a running ceph three-node cluster with two ssd storage nodes and one monitor.
What I would like to achieve is adding another two storage nodes with spinning drives and create a new pool and keep these two pools separated.
I suppose I need to edit crushmap something like here...
Hi,
I am experiencing another problem with gui. I run unregular backup of one of my vm during the night and it shows task ok. But the task seems still active in the tasks part.
Moreover my cluster seems to be disconnected via GUI. Another servers are red and all vm are shown just like a...
Hi,
I want to achieve running HA VM just on selected nodes and not on ceph nodes, or just have these nodes as a "disaster" backup.
I found on this page http://pve.proxmox.com/wiki/Ceph_Server following sentence:
If you do not want to run virtual machines and Ceph on the same host, you can just...
Hi,
I have configured three node cluster with ipmi fencing. I did some tests and I experienced some problems and I did not found answers to my newbie questions here, on wiki or via google.
I put one running kvm to HA list and it got started again, in fact restarted. Is this a correct behavior...
Hi,
I created a striped zfs pool on two nodes and then put replicated glusterfs on top. This is just testing cluster so no spare drive or raidz.
I tried to pull out one drive, the pool got into unavailable state and all vms on top of glusterfs froze.
I discovered that I need to set failmode to...
Hi,
I want to configure an active-backup bonding interface on proxmox 3.3 running kernel 3.10 and I need to select primary slave as it is a faster card connected to a faster switch. But unfortunately as a primary slave it is automatically selected interface with lower number, in my case eth2...
Hi,
I had to restore some files from a backup but I was unable to find any completely working howto here or on the wiki, which is a pitty imo.
This is my working solution for a vm without LVM (howto for LVM http://alexeytorkhov.blogspot.cz/2009/09/mounting-raw-and-qcow2-vm-disk-images.html ) ...
Hi,
I have currently three node cluster, one node on 3.3 and two on 3.2.
It was running without any problem but today I had to restart one nfs server.
I received some error logs about vanished connections and servers stopped to "see" each other on the web page.
I experienced this few months...
Hi,
I am now in process of migrating some machines from proxmox 3.2 to proxmox 3.3. With one machine I have a following error after reaching 100%:
qmp command 'block-job-complete' failed - The active block job for device 'drive-virtio0' cannot be completed
I have successfully done live...
Hi,
I have problems with backing up my guests. My architecture now consists of two servers and on one server is virtual guest with pass-through controller running debian installed on local drive (just a sidenote: I made some benchmarks of nfs and a difference in performance between zfs on...
Hello,
I have a problem mounting glusterfs on one of my server in cluster. On one node it is mounted without any problem but on the other one I can find this messages in syslog
cluster3 pvestatd[558285]: WARNING: unable to activate storage 'zalohysun' - directory '/mnt/pve/zalohysun' does not...
Hi,
as I can not login to gui for few days on either server (no HA) I would like to try migrate containers to second node and reboot first one. I was searching on this forum but I am unable to find proper command. I have just found that I should use pvectl insted of vzmigrate but I have not...
Hi all,
last two days I have a problem to login via gui. I created a cluster, no HA, and everything was working (well two linux KVM guest - at all I have around twenty kvm guests and five openvz containers - got problems, that they were not backed up and they were shutted down during that, but...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.