Search results

I've spent the last hour following dead ends but I would like to use the HDMI output on M70Q for my windows 11 video. I do not have an add on graphics card, so I'm trying to use the intel 630 built in to the M70Q. I have windows 11 running fine using remote terminal support or through the...

I am currently running Home Assistant (production) and WIndows 11 (test/development) on my Nuc8i5. I run windows 11 remotely from my desktop..if I need to access it directly from the NUC, I use the proxmox console function. Home Assistant just runs and is managed remotely. I would like to set...

I would like to set up my nuc with proxmox and use my desktop display in a VM. I currently have proxmox assigned to the desktop display. Is it possible to set Proxmox to use a USB/hdmi adapter?? If I can do that, then I should be able to assign the builit in adapter to the VM....I hope :)

I have proxmox 7.x installed on a nuc8 with 32gb and 1TB NVME. All is well, running windows 11, home assistant,.... I just put a 1tb sata drive in the NUC and would like to use it for backup. I'm a bit of a newbe at this. How do I activate that sata drive to do the backups? If I kill...

I have a NUC8 set up with windows 11 for testing....and I use windows 11 operationally on my desk. I would like to access the windows test system on the NUC using RDC from my desktop. I've enabled remoted desktop connection and I've checked that it's passed through windows defender. the...

Is it possible to assign proxmox graphics to a usb/hdmi adapter and assign the internal graphics on my NUC8 to my hackintosh VM? If so....pls point me to some "how to do this" page.

I have multiple VM's and LXE's working on my NUC with Proxmox 7...and everything worked fine yesterday. This morning, I can no longer get to IP:8006 but all of the VM's are working fine with full LAN access. Looking at my router, I see all of the VM ip's, but I don't see Proxmox itself or...

How do I see all of the network IP's being requested by proxmox? I deleted an LXC and installed the same software on a new (different number) CT.....but after rebooting both my router and proxmox system, I still see the old IP assigned and active when looking at the router. I have the...

I am trying to run home assistant and pfSense on the same system (NUC8i5). Home Assistant uses a USB z-wave dongle...and pfSense is using a startech USB dual NIC. Each runs fine alone. If I start both of them, at some point minutes to hours later, Home Assistant loses contact with the z-wave...

I am trying to install windows 11 on Proxmox 7.1 on a NUC8i5. however I am unable to select where I want windows installed. I found a driverdisk (red hat?) and loaded the vioscsi AMD64 drivers but those drivers still don't show any disk to load windows. What drivers should I use to install

I've installed Proxmox 7.1 and set up a new VM. Doing the install off a USB stick. I get the following error message. BdsDxe: failed to load Boot0003 "UEFI Misc Device" from PciRoot(0x0.......... I'm pretty new to proxmox and followed a "cookbook" with win11 on my USB stick...and I've...

I want to use my NUC7i5 to run Home Assistant and I want to run KODI on the same NUC. Unfortunately, Home Assistant runs under Debian and I need to run KODI 18.x which requires Ubuntu (Only KODI 17.x is supported on Debian). I’ve been trying to work with Proxmox…two VM’s, one for HA, the other...

I want to use the display attached to my NUC 7i5 with my Ubuntu container. I'm running Proxmox 6.3 running with three containers and no problems. There are a few posts on how to do graphics passthru...mostly for Nuc8's and Windows systems and even those are incomplete or inconsistent. My...

I've installed full debian on top of Proxmox because this is my desktop development system, a NUC with one NIC and one graphic card/display. I've created two containers....one with home assistant, the other with PiHole. Their IP addresses are: Debian/Proxmox 192.168.254.200 PiHole...

I've installed debian on Proxmox...this will be my development system (NUC i5). I have Home Assistant running in a container and I run the full debian desktop when I boot the system. I manage Proxmox from my windows system through the web inteface :8006. Two issues that are related: If I run...

I have a new NUC7i5 with 32mb memory and 1tb storage and I think/hope Proxmox is the key to what I want to do. The hardware limitations I'm concerned about: one graphics adapter with one display (my TV) and one ethernet port. I would like to run the following on the NUC: 1) home assistant...

I've installed Proxmox, a home assistant VM, and a debian 10 lxc with PiHole in docker on an older nuc. All run fine.....but I need to use the single display on the NUC (my TV) as the Debian (or other) graphic console allowing me to show internet video on my TV (YouTube, etc). I chose...

I have Proxmox installed and I have three containers...100 has home assistant running; 101 and 102 both have Debian 10 installed. I want to use 101 and 102 for testing...I will install other linux systems in one of those....debian 10 in both is just a place holder. Here's where I'm lost: I...

I installed Proxmox and a container with Home Assistant. I added (not sure if I should have) gnome to proxmox. I am now trying to create a second container with debian and a variety of desktops, just to try them. I have created the new container with Debian and added a network device Vmbr0...