Search results

addendum, yes, that was the issue. problem/query solved. now, trying to figure out how that entry was placed there.

resolve , as meaning /dev/sda1 would be / and /dev/sda5 become the swap partition.

I recently noticed the / partition being labelled /dev/sdb1, and I think I figured it out. for some reason I have an entry in fstab. If I simply remove the line refencing sdb , would that resolve the issue ? cat /etc/fstab # /etc/fstab: static file system information. # # Use 'blkid' to...

correct, I hadn't thought it through. backup via the management gui, and then delete the VM's. thanks

I have a few vms I don't think I need, however, I want to have a copy , just in case, so how can I copy vm-124 vm & vm-126 to another attached disk on the pve , before I remove them from gui ? 102 & 175 are being used, thus needed. lvs /dev/sdf: open failed: No medium found /dev/sdg: open...

I have figured it out, from the gui, I go to the listed storage devices, and it showed up in there , and was able to delete it.

I had deleted a vm via the gui console ( vmid 104), however from the command line it still appears, and If I tryto add anew vm, there isn't enough disk. any ideas ? and yes I want to delete the vm 104. thank you root@pve:/# qm list VMID NAME STATUS MEM(MB)...

proxmox 6.4 is considered old now, ok there is a reason the centos has to be version 6, I m well aware of its age

I have a proxmox 6.4-12 host, and several vms. I can do the hard disk passthrough wit the other vms, ( current debian) but unable to on a centos6 vm, any ideas why ? I get the following error. mount /dev/sdb /tempz mount: wrong fs type, bad option, bad superblock on /dev/sdb, missing...

update the down grade of qemu to 6.0.0-4 did not improvethe system, as it froze again, the only improvement is, it took longer to do so. back to the drawing board or pve 6.4

update, so far so good. in the last few days, the transfer would not have lasted this long, appears to be good. will test with another large file(s) and update later.

I just saw the post on downgrading , will do and report back

I am seeing same sort of issues on a clean 7.1.7 install. What I am experiencing is the pve freezing while transferring data to a debian vm running samba. It may run for 5 minutes, it may run for 1/2 hour. It freezes, and I have not seen anything of value in the log. perhaps I am looking in the...

sigh, humbled again. as I look closer at this, my ignorance is displayed. thank you for your time.

actually no, one nic is connected to the ISP/internet/wan and the other is connected to the internal lan

I had a working proxmox setup in my lab, and then I moved it to be in production. This is the intended setup. proxmox pve ( I call host) just manages the vm's. I have 2 vm's. vm1 will be a debian gw and firewall, and also run samba for the internal lan. I am not sure what I have "pooched"...

not quite sure what I did, however, when I added another nic to the server, I was able to get access again. It appears to me, the networking is fubar, so I have re-installed. What I want to do is as follows. I have 2 interfaces eno1 & eno2. eno1 is the internet facing interface and eno2 will be...

Thanks Fabian, you are correct. I did not read through all the documentation. I (sheepishly admit) added a new storage ( data2) and it worked. I am trying to get used to the gui, however I do prefer the command line in most instances. I will need to play/experiment with it. I suspect I can...

I am trying to restore a vm to a different host. I used the following, I suspect I need to create a storage "data2", on the new host. restore vma archive: zstd -q -d -c /mnt/pve/samba2/dump/vzdump-qemu-101-2021_03_07-16_54_46.vma.zst | vma extract -v -r /var/tmp/vzdumptmp12518.fifo -...

I seemed to have 'hooped' my network config. I have edited the host file, and the /etc/network/interfaces to see if I can get the management gui back, but no luck, is there a document with just a minimal config ? command preferred.