I'm not very good with how Apparmor works, so I was hoping someone might help me solve this one.
Two of my many LXC containers, ID 110 and ID 170 are resulting in an absolute spamming of DMESG as follows:
Please see this pastebin. It was too much to post in a message here.
I have been running a somewhat complex network setup on my server for some time:
2x Copper Gigabit Ethernet on Server Board
4x Copper Gigabit Ethernet (Intel 4x PRO/1000 NIC)
1x 10GBaseT Intel 82598EB
I'm not going to go into the details of what they are used for, as it is not...
I have an existing very complicated container, with lots of interfaces and mounts. It's running on Ubuntu 14.04 LTS which is about to go EOL.
I have tried ZFS snapshotting the existing containers rpool/subvol-110-disk-1 location and doing an in place upgrade but it...
So, I know you configure the network interfaces for new containers in the web interface (or by editing the corresponding config file in /etc/pve/lxc) but how does it work when you actually power up the container?
The reason I ask is, I have a bunch of Ubuntu 14.04 based containers...
Is this advisable?
The reason I ask is, I'm not sure I fully understand how the PVE frontend configures the containers network and other settings.
14.04 and 16.04 use ifup/down and are thus configured in /etc/network/interfaces, but 18.04 replaces ifup/down with netplan, which is...
I have a quick question.
I have a container with a rather complex configuration with many mounted folders, and several Ethernet devices. I'd like the keep the container as is, but replace the template it is running off of with a different distribution.
Is this possible?
I have a ZFS pool in my proxmox box consisting of Seagate Enterprise drives.
They accept the smartctl -l scterc command to set the error recovery timeout, but unfortunately for some reason it is not persistent after reboot.
While reboots are infrequent, I don't want to forget to...
First let me explain my setup. My Proxmox box boots off of a ZFS mirror of two 500GB SSD's. I also have a secondary ZFS pool consisting of 12 spinning disks, 2 SSD SLOG ZIL devices and 2 SSD L2ARC devices, which I use for data storage. I am in the middle of a slow project to one...
I installed Proxmox to a mirrored pair of SSD's quite a while ago. I noticed almost immediately that the resultant rpool used old fashioned linux device names:
NAME STATE READ WRITE CKSUM
rpool ONLINE 0 0 0
mirror-0 ONLINE 0 0...
So I've had the following setup working for quite some time.
1.) ZFS pool on host shared via NFS to QEMU VM.
2.) QEMU VM mounts NFS share, reverse encrypts the file system using encfs and exports it via NFS to a Ubuntu Server LXC container.
3.) LXC container runs cloud backup...
Can anyone help me troubleshoot this? I downloaded the turnkey linux openvpn template from the PVE web interface and installed it into a new LXC container.
I believe I set it up as a host correctly using the first time configuration in the console, and my port forward rule for port...
I'm having a little bit of difficulty getting something to work the way I need it to.
I have two containers. Let's call them LXC1 and LXC2.
LXC1 runs a software that creates files I need to access in LXC2.
LXC1 writes these files to a folder on the host.
The problem is, that the...
I often use my workstation to transfer large amounts of data to and from my Proxmox server, and anything I can do to speed it up would greatly help me.
My workstation runs Linux Mint 18, with two intel NIC's bonded in 802.3ad mode with my Procurve switch.
My Proxmox server has the...
Hey all, I am trying to run ntopng in an LXC container, but no matter how I try
router -> Switch -> everything else.
Using the switch I have mirrored the port connected to the router to another port. I ahve connected an Ethernet cable to this port, and connected ti to a dedicated...
I am trying to run ntopng in an Ubuntu 14.04LTS container on my Proxmosx host.
I set up my switch (Procurve 1810G-24) to mirror both RX and TX of the port connected to my router, to a separate port on the switch.
Then I connected a designated NIC (eth3) on my Proxmox box to that...
I am having an odd problem I'm hopng someone might help me solve.
I keep randomly getting "Error: No space left on device" error messages in console.
# ifup vmbr3
Waiting for vmbr3 to get ready (MAXWAIT is 2 seconds).
Error: No space left on device
Error: No space left on...
Personally I always like to take precautions whenever I upgrade something to make sure that package updates don't break anything for me.
I've been wondering, on a ZFS based install, is snapshotting rpool/ROOT/pve-1 a good way of accomplishing this?
In theory, I could run the...
So I just tried installing Ubuntu in OVMF mode for the first time. I went into the options screen and changed SeaBios to OVMF and then started my install.
The install ISO appeared to boot in UEFI mode properly, and th einstall proceeded as normal. The only difference was the...
I have been following the guide in the Proxmox Wiki on the topic, but I have run into issues.
First off, let me share my plan:
My proxmox box will also serve as a HTPC for two different TV's using two separate Geforce 720 GT cards passed through to VM's running Ubuntu and KODI...
So I know the two common methods of USB pass through are either on a per device basis using the USB device ID, or to pass through an entire USB controller, so that any devices plugged into that controller show up in the VM not in the host.
I have some problems with both of these...