Why is not nic not seen?

brephil

Member
Apr 24, 2021
21
0
6
53
See the following [03:00.1 and 03:00.1]:

Code:
root@pvenode02:~# lspci -k| sed -n '/Ethernet/,/driver in use/p'

03:00.0 Ethernet controller: Intel Corporation Ethernet Controller 10-Gigabit X540-AT2 (rev 01)

        Subsystem: Super Micro Computer Inc Ethernet Controller 10-Gigabit X540-AT2

        Kernel driver in use: ixgbe

03:00.1 Ethernet controller: Intel Corporation Ethernet Controller 10-Gigabit X540-AT2 (rev 01)

        Subsystem: Super Micro Computer Inc Ethernet Controller 10-Gigabit X540-AT2

        Kernel driver in use: ixgbe

82:00.0 Ethernet controller: Intel Corporation 82580 Gigabit Network Connection (rev 01)

        Subsystem: Hewlett-Packard Company NC365T 4-port Ethernet Server Adapter

        Kernel driver in use: igb

82:00.1 Ethernet controller: Intel Corporation 82580 Gigabit Network Connection (rev 01)

        Subsystem: Hewlett-Packard Company NC365T 4-port Ethernet Server Adapter

        Kernel driver in use: igb

82:00.2 Ethernet controller: Intel Corporation 82580 Gigabit Network Connection (rev 01)

        Subsystem: Hewlett-Packard Company NC365T 4-port Ethernet Server Adapter

        Kernel driver in use: igb

82:00.3 Ethernet controller: Intel Corporation 82580 Gigabit Network Connection (rev 01)

        Subsystem: Hewlett-Packard Company NC365T 4-port Ethernet Server Adapter

        Kernel driver in use: igb

I can only see the second 10-Gigbit NIC when I use the ip command , or is it the eno1? [expecting enp3s0f0]:

Code:
root@pvenode02:~# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: enp130s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master vmbr0 state UP mode DEFAULT group default qlen 1000
    link/ether ac:16:2d:93:6f:0c brd ff:ff:ff:ff:ff:ff
3: enp130s0f1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
    link/ether ac:16:2d:93:6f:0d brd ff:ff:ff:ff:ff:ff
4: enp130s0f2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
    link/ether ac:16:2d:93:6f:0e brd ff:ff:ff:ff:ff:ff
5: enp130s0f3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
    link/ether ac:16:2d:93:6f:0f brd ff:ff:ff:ff:ff:ff
6: eno1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
    link/ether 3c:ec:ef:1b:c6:dc brd ff:ff:ff:ff:ff:ff
7: enp3s0f1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 qdisc mq master vmbr2 state UP mode DEFAULT group default qlen 1000
    link/ether 3c:ec:ef:1b:c6:dd brd ff:ff:ff:ff:ff:ff
8: vmbr0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
    link/ether ac:16:2d:93:6f:0c brd ff:ff:ff:ff:ff:ff
9: vmbr2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 qdisc noqueue state UP mode DEFAULT group default qlen 1000
    link/ether 3c:ec:ef:1b:c6:dd brd ff:ff:ff:ff:ff:ff
10: tap108i0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 9000 qdisc pfifo_fast master fwbr108i0 state UNKNOWN mode DEFAULT group default qlen 1000
    link/ether c2:e9:92:38:11:c4 brd ff:ff:ff:ff:ff:ff
11: fwbr108i0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 qdisc noqueue state UP mode DEFAULT group default qlen 1000
    link/ether e2:ec:f2:62:1f:8a brd ff:ff:ff:ff:ff:ff
12: fwpr108p0@fwln108i0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 qdisc noqueue master vmbr2 state UP mode DEFAULT group default qlen 1000
    link/ether 32:dd:b7:14:70:51 brd ff:ff:ff:ff:ff:ff
13: fwln108i0@fwpr108p0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 qdisc noqueue master fwbr108i0 state UP mode DEFAULT group default qlen 1000
    link/ether e2:ec:f2:62:1f:8a brd ff:ff:ff:ff:ff:ff

I cannot figre this out.. no I do not have this pci devicxe listed as a pass through for any VMs do not even have IOMMU enabled yet.
 
Well that is odd, the second 10Gb nic is that eno1 (used ethtool to figure out it is a 10G nic)... why is that?

where do these names come from?
 
hi,

I can only see the second 10-Gigbit NIC when I use the ip command , or is it the eno1? [expecting enp3s0f0]:
yes it seems to be eno1

here your two bridge interfaces:
Code:
8: vmbr0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
    link/ether ac:16:2d:93:6f:0c brd ff:ff:ff:ff:ff:ff
9: vmbr2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 qdisc noqueue state UP mode DEFAULT group default qlen 1000
    link/ether 3c:ec:ef:1b:c6:dd brd ff:ff:ff:ff:ff:ff

note the MAC addresses. and the respective interfaces:
Code:
2: enp130s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master vmbr0 state UP mode DEFAULT group default qlen 1000
    link/ether ac:16:2d:93:6f:0c brd ff:ff:ff:ff:ff:ff
6: eno1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
    link/ether 3c:ec:ef:1b:c6:dc brd ff:ff:ff:ff:ff:ff

where do these names come from
can you show us your network configuration from /etc/network/interfaces ?
 

About

The Proxmox community has been around for many years and offers help and support for Proxmox VE, Proxmox Backup Server, and Proxmox Mail Gateway.
We think our community is one of the best thanks to people like you!

Get your subscription!

The Proxmox team works very hard to make sure you are running the best software and getting stable updates and security enhancements, as well as quick enterprise support. Tens of thousands of happy customers have a Proxmox subscription. Get yours easily in our online shop.

Buy now!