can not aptitude full upgrade on a new install ** SOLVED **

R

RobFantini

Famous Member
May 24, 2012
2,042
107
133
Boston,Mass
the issue was caused by a large /etc/ssh/ssh_known_hosts file.

we use a site wide known_hosts which is rsynced to all systems.

Udo figured out the issue.
------------------------------------------------------------------------------------

Hello
on a fresh install when this is run:
Code: 
aptitude full upgrade
We get the error below.

I tried reinstall and ran in to the same issue.

I'm not using backports just the sources.list from new install.

Any suggestion to get around this?

Code: 
The following partially installed packages will be configured:
  fence-agents-pve libpve-access-control proxmox-ve-2.6.32 pve-cluster pve-manager qemu-server redhat-cluster-pve 
No packages will be installed, upgraded, or removed.
0 packages upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
Need to get 0 B of archives. After unpacking 0 B will be used.
Setting up pve-cluster (1.0-27) ...
Restarting pve cluster filesystem: pve-cluster.
input too long - aborting
dpkg: error processing pve-cluster (--configure):
 subprocess installed post-installation script returned error exit status 255
configured to not write apport reports
                                      dpkg: dependency problems prevent configuration of redhat-cluster-pve:
 redhat-cluster-pve depends on pve-cluster; however:
  Package pve-cluster is not configured yet.
dpkg: error processing redhat-cluster-pve (--configure):
 dependency problems - leaving unconfigured
dpkg: dependency problems prevent configuration of fence-agents-pve:
 fence-agents-pve depends on redhat-cluster-pve; however:
  Package redhat-cluster-pve is not configured yet.
dpkg: error processing fence-agents-pve (--configure):
 dependency problems - leaving unconfigured
dpkg: dependency problems prevent configuration of libpve-access-control:
 libpve-access-control depends on pve-cluster; however:
  Package pve-cluster is not configured yet.
dpkg: error processing libpve-access-control (--configure):
 dependency problems - leaving unconfigured
configured to not write apport reports
                                      configured to not write apport reports
                                                                            configured to not write apport reports
                                                                                                                  dpkg: dependency problems prevent configuration of qemu-server:
 qemu-server depends on pve-cluster; however:
  Package pve-cluster is not configured yet.
 qemu-server depends on redhat-cluster-pve; however:
  Package redhat-cluster-pve is not configured yet.
dpkg: error processing qemu-server (--configure):
 dependency problems - leaving unconfigured
configured to not write apport reports
                                      dpkg: dependency problems prevent configuration of pve-manager:
 pve-manager depends on qemu-server (>= 1.1-1); however:
  Package qemu-server is not configured yet.
 pve-manager depends on pve-cluster; however:
  Package pve-cluster is not configured yet.
 pve-manager depends on libpve-access-control; however:
  Package libpve-access-control is not configured yet.
 pve-manager depends on redhat-cluster-pve; however:
  Package redhat-cluster-pve is not configured yet.
 pve-manager depends on fence-agents-pve; however:
  Package fence-agents-pve is not configured yet.
dpkg: error processing pve-manager (--configure):
 dependency problems - leaving unconfigured
configured to not write apport reports
                                      dpkg: dependency problems prevent configuration of proxmox-ve-2.6.32:
 proxmox-ve-2.6.32 depends on pve-manager; however:
  Package pve-manager is not configured yet.
 proxmox-ve-2.6.32 depends on qemu-server; however:
  Package qemu-server is not configured yet.
dpkg: error processing proxmox-ve-2.6.32 (--configure):
 dependency problems - leaving unconfigured
configured to not write apport reports
                                      Errors were encountered while processing:
 pve-cluster
 redhat-cluster-pve
 fence-agents-pve
 libpve-access-control
 qemu-server
 pve-manager
 proxmox-ve-2.6.32
E: Sub-process /usr/bin/dpkg returned an error code (1)
A package failed to install.  Trying to recover:
Setting up pve-cluster (1.0-27) ...
Restarting pve cluster filesystem: pve-cluster.
input too long - aborting
dpkg: error processing pve-cluster (--configure):
 subprocess installed post-installation script returned error exit status 255
dpkg: dependency problems prevent configuration of pve-manager:
 pve-manager depends on pve-cluster; however:
  Package pve-cluster is not configured yet.
dpkg: error processing pve-manager (--configure):
 dependency problems - leaving unconfigured
dpkg: dependency problems prevent configuration of proxmox-ve-2.6.32:
 proxmox-ve-2.6.32 depends on pve-manager; however:
  Package pve-manager is not configured yet.
dpkg: error processing proxmox-ve-2.6.32 (--configure):
 dependency problems - leaving unconfigured
dpkg: dependency problems prevent configuration of libpve-access-control:
 libpve-access-control depends on pve-cluster; however:
  Package pve-cluster is not configured yet.
dpkg: error processing libpve-access-control (--configure):
 dependency problems - leaving unconfigured
dpkg: dependency problems prevent configuration of qemu-server:
 qemu-server depends on pve-cluster; however:
  Package pve-cluster is not configured yet.
dpkg: error processing qemu-server (--configure):
 dependency problems - leaving unconfigured
dpkg: dependency problems prevent configuration of redhat-cluster-pve:
 redhat-cluster-pve depends on pve-cluster; however:
  Package pve-cluster is not configured yet.
dpkg: error processing redhat-cluster-pve (--configure):
 dependency problems - leaving unconfigured
dpkg: dependency problems prevent configuration of fence-agents-pve:
 fence-agents-pve depends on redhat-cluster-pve; however:
  Package redhat-cluster-pve is not configured yet.
dpkg: error processing fence-agents-pve (--configure):
 dependency problems - leaving unconfigured
Errors were encountered while processing:
 pve-cluster
 pve-manager
 proxmox-ve-2.6.32
 libpve-access-control
 qemu-server
 redhat-cluster-pve
 fence-agents-pve
 
Last edited:
Re: can not aptitude full upgrade on a new install

also hostname is s008

and this line is in /etc/hosts:
10.100.100.8 s008.fantinibakery.com s008 pvelocalhost
 
Re: can not aptitude full upgrade on a new install

of course you did a:
Code: 
aptitude update
first?
If not, try aptitude update and then aptitude full-upgrade.
You can also try aptitude -f install to try to fix the issue, that is really strange on a new system (and I've no idea about)
 
Re: can not aptitude full upgrade on a new install

mmenaz -
thanks for the reply.

I did an aptitude update.

On the 1-st aptitude full-upgrade, as expected many Debian packages were updated.

Just tried aptitude -f and :
Code: 
s008  /var/log/apt # aptitude -f install proxmox-ve-2.6.32
The following partially installed packages will be configured:
  fence-agents-pve libpve-access-control proxmox-ve-2.6.32 pve-cluster pve-manager qemu-server redhat-cluster-pve 
No packages will be installed, upgraded, or removed.
0 packages upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
Need to get 0 B of archives. After unpacking 0 B will be used.
Setting up pve-cluster (1.0-27) ...      
Restarting pve cluster filesystem: pve-cluster.
input too long - aborting
dpkg: error processing pve-cluster (--configure):
 subprocess installed post-installation script returned error exit status 255
configured to not write apport reports
                                      dpkg: dependency problems prevent configuration of redhat-cluster-pve:
 redhat-cluster-pve depends on pve-cluster; however:
  Package pve-cluster is not configured yet.
...
dpkg: error processing fence-agents-pve (--configure):
 dependency problems - leaving unconfigured
Errors were encountered while processing:
 pve-cluster
 pve-manager
 proxmox-ve-2.6.32
 libpve-access-control
 qemu-server
 redhat-cluster-pve
 fence-agents-pve

this is strange.
 
Re: can not aptitude full upgrade on a new install

RobFantini said:
mmenaz -
thanks for the reply.

I did an aptitude update.

On the 1-st aptitude full-upgrade, as expected many Debian packages were updated.

Just tried aptitude -f and :
Code: 
s008  /var/log/apt # aptitude -f install proxmox-ve-2.6.32
The following partially installed packages will be configured:
  fence-agents-pve libpve-access-control proxmox-ve-2.6.32 pve-cluster pve-manager qemu-server redhat-cluster-pve 
No packages will be installed, upgraded, or removed.
0 packages upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
Need to get 0 B of archives. After unpacking 0 B will be used.
Setting up pve-cluster (1.0-27) ...      
Restarting pve cluster filesystem: pve-cluster.
input too long - aborting
dpkg: error processing pve-cluster (--configure):
 subprocess installed post-installation script returned error exit status 255
configured to not write apport reports
                                      dpkg: dependency problems prevent configuration of redhat-cluster-pve:
 redhat-cluster-pve depends on pve-cluster; however:
  Package pve-cluster is not configured yet.
...
dpkg: error processing fence-agents-pve (--configure):
 dependency problems - leaving unconfigured
Errors were encountered while processing:
 pve-cluster
 pve-manager
 proxmox-ve-2.6.32
 libpve-access-control
 qemu-server
 redhat-cluster-pve
 fence-agents-pve

this is strange.
Click to expand...
Hi,
does the same happens with
Code: 
apt-get dist-upgrade
?
Udo
 
Re: can not aptitude full upgrade on a new install

Udo.
/etc/pve/cluster.conf does not exist :
Code: 
ls -l /etc/pve 
s008  ~ # ls -l /etc/pve
total 3
-rw-r----- 1 root www-data  451 Sep 15 10:58 authkey.pub
-rw-r----- 1 root www-data   16 Sep 15 10:56 datacenter.cfg
lrwxr-x--- 1 root www-data    0 Dec 31  1969 local -> nodes/s008
drwxr-x--- 2 root www-data    0 Sep 15 10:58 nodes
lrwxr-x--- 1 root www-data    0 Dec 31  1969 openvz -> nodes/s008/openvz
drwx------ 2 root www-data    0 Sep 15 10:58 priv
-rw-r----- 1 root www-data 1533 Sep 15 10:58 pve-root-ca.pem
-rw-r----- 1 root www-data 1679 Sep 15 10:58 pve-www.key
lrwxr-x--- 1 root www-data    0 Dec 31  1969 qemu-server -> nodes/s008/qemu-server
-rw-r----- 1 root www-data   49 Sep 15 10:56 user.cfg
-rw-r----- 1 root www-data  119 Sep 15 10:58 vzdump.cron

/etc/hosts on our systems is large, and too big to post the entire file. [ we append a local network hosts file .]
but here is the top part:
Code: 
10.100.100.8 s008.fantinibakery.com s008   pvelocalhost
127.0.0.1 localhost.localdomain localhost
# The following lines are desirable for IPv6 capable hosts
::1     localhost ip6-localhost ip6-loopback
fe00::0 ip6-localnet
ff00::0 ip6-mcastprefix
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters
ff02::3 ip6-allhosts

here is /etc/hostname :
Code: 
s008  ~ # cat /etc/hostname
s008
 
Last edited:
Re: can not aptitude full upgrade on a new install

RobFantini said:
/etc/hosts on our systems is large, and too big to post the entire file. [ we append a local network hosts file .]
Click to expand...

How large? That file is expected to be small, so please try/test with a small file.
 
Re: can not aptitude full upgrade on a new install

dietmar said:
How large? That file is expected to be small, so please try/test with a small file.
Click to expand...

the file is 61K .

We have 5 other proxmox systems with the same sized file and no issues.

I just now copied the the original hosts file back and have the same issue. here is that /etc/hosts :
Code: 
127.0.0.1 localhost.localdomain localhost
10.100.100.8 s008.fantinibakery.com s008 pvelocalhost


# The following lines are desirable for IPv6 capable hosts


::1     ip6-localhost ip6-loopback
fe00::0 ip6-localnet
ff00::0 ip6-mcastprefix
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters
ff02::3 ip6-allhosts

hostname = s008 for this system .
 
Re: can not aptitude full upgrade on a new install

Next I'll try rebooting s008 in case that helps.

result: same :
Code: 
The following partially installed packages will be configured:
  fence-agents-pve libpve-access-control proxmox-ve-2.6.32 pve-cluster pve-manager qemu-server redhat-cluster-pve 
No packages will be installed, upgraded, or removed.
0 packages upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
Need to get 0 B of archives. After unpacking 0 B will be used.
Setting up pve-cluster (1.0-27) ...
Restarting pve cluster filesystem: pve-cluster.
input too long - aborting
dpkg: error processing pve-cluster (--configure):
 subprocess installed post-installation script returned error exit status 255
 
Re: can not aptitude full upgrade on a new install

RobFantini said:
Next I'll try rebooting s008 in case that helps.

result: same :
Code: 
The following partially installed packages will be configured:
  fence-agents-pve libpve-access-control proxmox-ve-2.6.32 pve-cluster pve-manager qemu-server redhat-cluster-pve 
No packages will be installed, upgraded, or removed.
0 packages upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
Need to get 0 B of archives. After unpacking 0 B will be used.
Setting up pve-cluster (1.0-27) ...
Restarting pve cluster filesystem: pve-cluster.
input too long - aborting
dpkg: error processing pve-cluster (--configure):
 subprocess installed post-installation script returned error exit status 255
Click to expand...
Hi,
can you post the output of following commands:
Code: 
grep /etc/pve /proc/mounts
grep `cat /etc/hostname` /etc/hosts
dpkg-reconfigure pve-cluster
dpkg -l | grep pve
Udo
 
Re: can not aptitude full upgrade on a new install

Code: 
grep /etc/pve /proc/mounts
/dev/fuse /etc/pve fuse rw,nosuid,nodev,relatime,user_id=0,group_id=0,default_permissions,allow_other 0 0


grep `cat /etc/hostname` /etc/hosts
10.100.100.8 s008.fantinibakery.com s008 pvelocalhost

dpkg-reconfigure pve-cluster
/usr/sbin/dpkg-reconfigure: pve-cluster is broken or not fully installed


dpkg -l | grep pve
ii  clvm                            2.02.95-1pve2                Cluster LVM Daemon for lvm2
ii  corosync-pve                    1.4.3-1                      Standards-based cluster framework (daemon and modules)
ii  dmsetup                         2:1.02.74-1pve2              Linux Kernel Device Mapper userspace library
iU  fence-agents-pve                3.1.8-1                      fence agents for redhat cluster suite
ii  libcorosync4-pve                1.4.3-1                      Standards-based cluster framework (libraries)
ii  libdevmapper1.02.1              2:1.02.74-1pve2              Linux Kernel Device Mapper userspace library
ii  libopenais3-pve                 1.1.4-2                      Standards-based cluster framework (libraries)
iU  libpve-access-control           1.0-24                       Proxmox VE access control library
ii  libpve-common-perl              1.0-30                       Proxmox VE base library
ii  libpve-storage-perl             2.0-31                       Proxmox VE storage management library
ii  lvm2                            2.02.95-1pve2                Linux Logical Volume Manager
ii  openais-pve                     1.1.4-2                      Standards-based cluster framework (daemon and modules)
iF  pve-cluster                     1.0-27                       Cluster Infrastructure for Proxmox Virtual Environment
ii  pve-firmware                    1.0-18                       Binary firmware code for the pve-kernel
ii  pve-kernel-2.6.32-11-pve        2.6.32-66                    The Proxmox PVE Kernel Image
ii  pve-kernel-2.6.32-14-pve        2.6.32-74                    The Proxmox PVE Kernel Image
iU  pve-manager                     2.1-14                       The Proxmox Virtual Environment
ii  pve-qemu-kvm                    1.1-8                        Full virtualization on x86 hardware
iU  redhat-cluster-pve              3.1.92-3                     Red Hat cluster suite
ii  resource-agents-pve             3.9.2-3                      resource agents for redhat cluster suite
ii  vzctl                           3.0.30-2pve5                 OpenVZ - server virtualization solution - control tools
 
Re: can not aptitude full upgrade on a new install

RobFantini said:
Code: 
grep /etc/pve /proc/mounts
/dev/fuse /etc/pve fuse rw,nosuid,nodev,relatime,user_id=0,group_id=0,default_permissions,allow_other 0 0


grep `cat /etc/hostname` /etc/hosts
10.100.100.8 s008.fantinibakery.com s008 pvelocalhost

dpkg-reconfigure pve-cluster
/usr/sbin/dpkg-reconfigure: pve-cluster is broken or not fully installed


dpkg -l | grep pve
ii  clvm                            2.02.95-1pve2                Cluster LVM Daemon for lvm2
ii  corosync-pve                    1.4.3-1                      Standards-based cluster framework (daemon and modules)
ii  dmsetup                         2:1.02.74-1pve2              Linux Kernel Device Mapper userspace library
iU  fence-agents-pve                3.1.8-1                      fence agents for redhat cluster suite
ii  libcorosync4-pve                1.4.3-1                      Standards-based cluster framework (libraries)
ii  libdevmapper1.02.1              2:1.02.74-1pve2              Linux Kernel Device Mapper userspace library
ii  libopenais3-pve                 1.1.4-2                      Standards-based cluster framework (libraries)
iU  libpve-access-control           1.0-24                       Proxmox VE access control library
ii  libpve-common-perl              1.0-30                       Proxmox VE base library
ii  libpve-storage-perl             2.0-31                       Proxmox VE storage management library
ii  lvm2                            2.02.95-1pve2                Linux Logical Volume Manager
ii  openais-pve                     1.1.4-2                      Standards-based cluster framework (daemon and modules)
iF  pve-cluster                     1.0-27                       Cluster Infrastructure for Proxmox Virtual Environment
ii  pve-firmware                    1.0-18                       Binary firmware code for the pve-kernel
ii  pve-kernel-2.6.32-11-pve        2.6.32-66                    The Proxmox PVE Kernel Image
ii  pve-kernel-2.6.32-14-pve        2.6.32-74                    The Proxmox PVE Kernel Image
iU  pve-manager                     2.1-14                       The Proxmox Virtual Environment
ii  pve-qemu-kvm                    1.1-8                        Full virtualization on x86 hardware
iU  redhat-cluster-pve              3.1.92-3                     Red Hat cluster suite
ii  resource-agents-pve             3.9.2-3                      resource agents for redhat cluster suite
ii  vzctl                           3.0.30-2pve5                 OpenVZ - server virtualization solution - control tools
Click to expand...
Ok,
can you run following with an short hosts-file?
Code: 
dpkg-reconfigure fence-agents-pve
dpkg-reconfigure libpve-access-control
dpkg-reconfigure redhat-cluster-pve
dpkg-reconfigure pve-manager
dpkg-reconfigure pve-cluster

# after that again
dpkg -l | grep pve
Udo
 
Re: can not aptitude full upgrade on a new install

udo said:
Ok,
can you run following with an short hosts-file?
Code: 
dpkg-reconfigure fence-agents-pve
dpkg-reconfigure libpve-access-control
dpkg-reconfigure redhat-cluster-pve
dpkg-reconfigure pve-manager
dpkg-reconfigure pve-cluster

# after that again
dpkg -l | grep pve
Udo
Click to expand...

Code: 
s008  /etc # cat hosts.ori
127.0.0.1 localhost.localdomain localhost
10.100.100.8 s008.fantinibakery.com s008 pvelocalhost

# The following lines are desirable for IPv6 capable hosts

::1     ip6-localhost ip6-loopback
fe00::0 ip6-localnet
ff00::0 ip6-mcastprefix
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters
ff02::3 ip6-allhosts
s008  /etc # dpkg-reconfigure fence-agents-pve
/usr/sbin/dpkg-reconfigure: fence-agents-pve is broken or not fully installed
s008  /etc # dpkg-reconfigure libpve-access-control
/usr/sbin/dpkg-reconfigure: libpve-access-control is broken or not fully installed
s008  /etc # dpkg-reconfigure redhat-cluster-pve
/usr/sbin/dpkg-reconfigure: redhat-cluster-pve is broken or not fully installed
s008  /etc # dpkg-reconfigure pve-manager
/usr/sbin/dpkg-reconfigure: pve-manager is broken or not fully installed
s008  /etc # dpkg-reconfigure pve-cluster
/usr/sbin/dpkg-reconfigure: pve-cluster is broken or not fully installed
 
Re: can not aptitude full upgrade on a new install

note /etc/hosts was the same as /etc/hosts.ori when I did the above.

cat /etc/hosts:
Code: 
s008  ~ # cat /etc/hosts
127.0.0.1 localhost.localdomain localhost
10.100.100.8 s008.fantinibakery.com s008 pvelocalhost

# The following lines are desirable for IPv6 capable hosts

::1     ip6-localhost ip6-loopback
fe00::0 ip6-localnet
ff00::0 ip6-mcastprefix
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters
ff02::3 ip6-allhosts

These errors occured with a clean install , as after the 1-st reboot , before doing anything else, I ran apptitude update and aptitude full-upgrade .
 
Re: can not aptitude full upgrade on a new install

Here is /var/log/aptitude showing initial full-upgrade:

Code: 
 Aptitude 0.6.3: log reportSat, Sep 15 2012 11:01:59 -0400


IMPORTANT: this log only lists intended actions; actions which fail due to
dpkg problems may not be completed.


Will install 73 packages, and remove 0 packages.
15.1 MB of disk space will be used
===============================================================================
[INSTALL, DEPENDENCIES] ceph-common
[INSTALL, DEPENDENCIES] libio-multiplex-perl
[INSTALL, DEPENDENCIES] libiscsi1
[INSTALL, DEPENDENCIES] librados2
[INSTALL, DEPENDENCIES] librbd1
[INSTALL, DEPENDENCIES] pve-kernel-2.6.32-14-pve
[UPGRADE] apache2 2.2.16-6+squeeze4 -> 2.2.16-6+squeeze7
[UPGRADE] apache2-mpm-prefork 2.2.16-6+squeeze4 -> 2.2.16-6+squeeze7
[UPGRADE] apache2-utils 2.2.16-6+squeeze4 -> 2.2.16-6+squeeze7
[UPGRADE] apache2.2-bin 2.2.16-6+squeeze4 -> 2.2.16-6+squeeze7
[UPGRADE] apache2.2-common 2.2.16-6+squeeze4 -> 2.2.16-6+squeeze7
[UPGRADE] at 3.1.12-1 -> 3.1.12-1+squeeze1
[UPGRADE] base-files 6.0squeeze4 -> 6.0squeeze5
[UPGRADE] bind9-host 1:9.7.3.dfsg-1~squeeze4 -> 1:9.7.3.dfsg-1~squeeze7
[UPGRADE] dnsutils 1:9.7.3.dfsg-1~squeeze4 -> 1:9.7.3.dfsg-1~squeeze7
[UPGRADE] fence-agents-pve 3.1.7-2 -> 3.1.8-1
[UPGRADE] file 5.04-5 -> 5.04-5+squeeze2
[UPGRADE] initscripts 2.88dsf-13.1 -> 2.88dsf-13.1+squeeze1
[UPGRADE] isc-dhcp-client 4.1.1-P1-15+squeeze3 -> 4.1.1-P1-15+squeeze6
[UPGRADE] isc-dhcp-common 4.1.1-P1-15+squeeze3 -> 4.1.1-P1-15+squeeze6
[UPGRADE] libapr1 1.4.2-6+squeeze3 -> 1.4.2-6+squeeze4
[UPGRADE] libbind9-60 1:9.7.3.dfsg-1~squeeze4 -> 1:9.7.3.dfsg-1~squeeze7
[UPGRADE] libc-bin 2.11.3-2 -> 2.11.3-3
[UPGRADE] libc6 2.11.3-2 -> 2.11.3-3
[UPGRADE] libc6-i386 2.11.3-2 -> 2.11.3-3
[UPGRADE] libcurl3-gnutls 7.21.0-2 -> 7.21.0-2.1+squeeze2
[UPGRADE] libdns69 1:9.7.3.dfsg-1~squeeze4 -> 1:9.7.3.dfsg-1~squeeze7
[UPGRADE] libexpat1 2.0.1-7 -> 2.0.1-7+squeeze1
[UPGRADE] libfreetype6 2.4.2-2.1+squeeze3 -> 2.4.2-2.1+squeeze4
[UPGRADE] libgnutls26 2.8.6-1+squeeze1 -> 2.8.6-1+squeeze2
[UPGRADE] libgssapi-krb5-2 1.8.3+dfsg-4squeeze5 -> 1.8.3+dfsg-4squeeze6
[UPGRADE] libgssrpc4 1.8.3+dfsg-4squeeze5 -> 1.8.3+dfsg-4squeeze6
[UPGRADE] libisc62 1:9.7.3.dfsg-1~squeeze4 -> 1:9.7.3.dfsg-1~squeeze7
[UPGRADE] libisccc60 1:9.7.3.dfsg-1~squeeze4 -> 1:9.7.3.dfsg-1~squeeze7
[UPGRADE] libisccfg62 1:9.7.3.dfsg-1~squeeze4 -> 1:9.7.3.dfsg-1~squeeze7
[UPGRADE] libk5crypto3 1.8.3+dfsg-4squeeze5 -> 1.8.3+dfsg-4squeeze6
[UPGRADE] libkadm5clnt-mit7 1.8.3+dfsg-4squeeze5 -> 1.8.3+dfsg-4squeeze6
[UPGRADE] libkadm5srv-mit7 1.8.3+dfsg-4squeeze5 -> 1.8.3+dfsg-4squeeze6
[UPGRADE] libkdb5-4 1.8.3+dfsg-4squeeze5 -> 1.8.3+dfsg-4squeeze6
[UPGRADE] libkrb5-3 1.8.3+dfsg-4squeeze5 -> 1.8.3+dfsg-4squeeze6
[UPGRADE] libkrb5support0 1.8.3+dfsg-4squeeze5 -> 1.8.3+dfsg-4squeeze6
[UPGRADE] liblwres60 1:9.7.3.dfsg-1~squeeze4 -> 1:9.7.3.dfsg-1~squeeze7
[UPGRADE] libmagic1 5.04-5 -> 5.04-5+squeeze2
[UPGRADE] libnss3-1d 3.12.8-1+squeeze4 -> 3.12.8-1+squeeze5
[UPGRADE] libpng12-0 1.2.44-1+squeeze1 -> 1.2.44-1+squeeze4
[UPGRADE] libpve-access-control 1.0-21 -> 1.0-24
[UPGRADE] libpve-common-perl 1.0-27 -> 1.0-30
[UPGRADE] libpve-storage-perl 2.0-18 -> 2.0-31
[UPGRADE] libssl0.9.8 0.9.8o-4squeeze7 -> 0.9.8o-4squeeze13
[UPGRADE] libtasn1-3 2.7-1 -> 2.7-1+squeeze+1
[UPGRADE] libxml2 2.7.8.dfsg-2+squeeze1 -> 2.7.8.dfsg-2+squeeze5
[UPGRADE] libxml2-utils 2.7.8.dfsg-2+squeeze1 -> 2.7.8.dfsg-2+squeeze5
[UPGRADE] locales 2.11.3-2 -> 2.11.3-3
[UPGRADE] openssh-client 1:5.5p1-6+squeeze1 -> 1:5.5p1-6+squeeze2
[UPGRADE] openssh-server 1:5.5p1-6+squeeze1 -> 1:5.5p1-6+squeeze2
[UPGRADE] openssl 0.9.8o-4squeeze7 -> 0.9.8o-4squeeze13
[UPGRADE] procps 1:3.2.8-9 -> 1:3.2.8-9squeeze1
[UPGRADE] proxmox-ve-2.6.32 2.0-66 -> 2.1-74
[UPGRADE] pve-cluster 1.0-26 -> 1.0-27
[UPGRADE] pve-firmware 1.0-15 -> 1.0-18
[UPGRADE] pve-manager 2.1-1 -> 2.1-14
[UPGRADE] pve-qemu-kvm 1.0-9 -> 1.1-8
[UPGRADE] python 2.6.6-3+squeeze6 -> 2.6.6-3+squeeze7
[UPGRADE] python-minimal 2.6.6-3+squeeze6 -> 2.6.6-3+squeeze7
[UPGRADE] qemu-server 2.0-39 -> 2.0-49
[UPGRADE] redhat-cluster-pve 3.1.8-3 -> 3.1.92-3
[UPGRADE] samba-common 2:3.5.6~dfsg-3squeeze6 -> 2:3.5.6~dfsg-3squeeze8
[UPGRADE] ssh 1:5.5p1-6+squeeze1 -> 1:5.5p1-6+squeeze2
[UPGRADE] sysv-rc 2.88dsf-13.1 -> 2.88dsf-13.1+squeeze1
[UPGRADE] sysvinit 2.88dsf-13.1 -> 2.88dsf-13.1+squeeze1
[UPGRADE] sysvinit-utils 2.88dsf-13.1 -> 2.88dsf-13.1+squeeze1
[UPGRADE] tzdata 2011n-0squeeze1 -> 2012c-0squeeze1
[UPGRADE] vncterm 1.0-2 -> 1.0-3
===============================================================================
Log complete.
Aptitude 0.6.3: log report
Sat, Sep 15 2012 11:03:26 -0400


IMPORTANT: this log only lists intended actions; actions which fail due to
dpkg problems may not be completed.


Will install 0 packages, and remove 0 packages.
===============================================================================
[UNCONFIGURED] fence-agents-pve
[UNCONFIGURED] libpve-access-control
[UNCONFIGURED] proxmox-ve-2.6.32
[UNCONFIGURED] pve-cluster
[UNCONFIGURED] pve-manager
[UNCONFIGURED] qemu-server
[UNCONFIGURED] redhat-cluster-pve
===============================================================================
[code]
 
Last edited:
Re: can not aptitude full upgrade on a new install

I think that somehow backports got enabled as the following pkg is a backport version.
Code: 
 aptitude show librbd1
Package: librbd1                         
New: yes
State: installed
Automatically installed: yes
Version: 0.48argonaut-1~bpo60+1

So I'll reinstall tomorrow and see if that solves the issue, and will report back.
 
Re: can not aptitude full upgrade on a new install

Udo
could you please run this on one of your proxmox systems?
Code: 
aptitude show librbd1

I assume it should not show a backports version.
 
Re: can not aptitude full upgrade on a new install

I just reinstalled. logged in and the 1-st command I ran :
Code: 
aptitude show librbd1
shows it is from backports. I ran into a non upgradable system a few months ago when backports were involved. But back then I had added a backports line to sources.list. This new install will probably pull in package updates which intefere with pve pkg upgrades.

next I'll run
Code: 
aptitude update
aptitude --simulate full-upgrade
to show what will get upgraded.

But to try to avoid the non upgradable system issue I'll try to just upgrade pve kernel then other pve packages one at a time.
 
Re: can not aptitude full upgrade on a new install

Code: 
s008  /etc # aptitude --simulate full-upgrade
The following NEW packages will be installed:
  ceph-common{a} libio-multiplex-perl{a} libiscsi1{a} librados2{a} librbd1{a} 
  pve-kernel-2.6.32-14-pve{a} 
The following packages will be upgraded:
  apache2 apache2-mpm-prefork apache2-utils apache2.2-bin apache2.2-common at base-files 
  bind9-host dnsutils fence-agents-pve file initscripts isc-dhcp-client isc-dhcp-common libapr1 
  libbind9-60 libc-bin libc6 libc6-i386 libcurl3-gnutls libdns69 libexpat1 libfreetype6 
  libgnutls26 libgssapi-krb5-2 libgssrpc4 libisc62 libisccc60 libisccfg62 libk5crypto3 
  libkadm5clnt-mit7 libkadm5srv-mit7 libkdb5-4 libkrb5-3 libkrb5support0 liblwres60 libmagic1 
  libnss3-1d libpng12-0 libpve-access-control libpve-common-perl libpve-storage-perl libssl0.9.8 
  libtasn1-3 libxml2 libxml2-utils locales openssh-client openssh-server openssl procps 
  proxmox-ve-2.6.32 pve-cluster pve-firmware pve-manager pve-qemu-kvm python python-minimal 
  qemu-server redhat-cluster-pve samba-common ssh sysv-rc sysvinit sysvinit-utils tzdata vncterm 
The following packages are RECOMMENDED but will NOT be installed:
  openssh-blacklist-extra samba-common-bin xml-core

I'm not going to to the full-upgrade as that would be insane to repeat.

So trying a part at a time, avoiding cluster packages:
Code: 
s008  /etc # aptitude safe-upgrade proxmox-ve-2.6.32 pve-firmware pve-manager pve-qemu-kvm qemu-server 
Resolving dependencies...                
The following NEW packages will be installed:
  ceph-common{a} libio-multiplex-perl{a} libiscsi1{a} librados2{a} librbd1{a} 
  pve-kernel-2.6.32-14-pve{a} 
The following packages will be upgraded:
  proxmox-ve-2.6.32 pve-firmware pve-manager pve-qemu-kvm qemu-server 
5 packages upgraded, 6 newly installed, 0 to remove and 62 not upgraded.
Need to get 57.0 MB of archives. After unpacking 13.9 MB will be used.
Do you want to continue? [Y/n/?] 
Get:1 http://ftp.us.debian.org/debian/ squeeze/main libio-multiplex-perl all 1.10-1 [23.8 kB]
Get:2 http://download.proxmox.com/debian/ squeeze/pve librados2 amd64 0.48argonaut-1~bpo60+1 [1,152 kB]
Get:3 http://download.proxmox.com/debian/ squeeze/pve librbd1 amd64 0.48argonaut-1~bpo60+1 [155 kB]
...

Installing new version of config file /etc/apache2/sites-available/pve.conf ...
Restarting PVE Daemon: pvedaemonCan't locate PVE/Storage/Plugin.pm in @INC (@INC contains: /etc/perl /usr/local/lib/perl/5.10.1 /usr/local/share/perl/5.10.1 /usr/lib/perl5 /usr/share/perl5 /usr/lib/perl/5.10 /usr/share/perl/5.10 /usr/local/lib/site_perl) at /usr/share/perl5/PVE/VZDump/QemuServer.pm line 11.
BEGIN failed--compilation aborted at /usr/share/perl5/PVE/VZDump/QemuServer.pm line 11.
Compilation failed in require at /usr/share/perl5/PVE/VZDump.pm line 32.
.
Restarting PVE Status Daemon: pvestatd.
Restarting web server: apache2 ... waiting .
Setting up proxmox-ve-2.6.32 (2.1-74) ...
installing proxmox release key: OK
                                         
Current status: 62 updates [-5].

that is an improvement. atleast most are upgraded.

next I'll upgrade all but redhat-cluster-pve ..

too bad that resulted in
Code: 
Setting up pve-cluster (1.0-27) ...
Restarting pve cluster filesystem: pve-clusterfuse: failed to access mountpoint /etc/pve: Transport endpoint is not connected
[main] crit: fuse_mount error: Transport endpoint is not connected
[main] notice: exit proxmox configuration filesystem (-1)

..
Errors were encountered while processing:
 pve-cluster
 libpve-access-control
E: Sub-process /usr/bin/dpkg returned an error code (1)
A package failed to install.  Trying to recover:
Setting up pve-cluster (1.0-27) ...
Restarting pve cluster filesystem: pve-clusterstart-stop-daemon: warning: failed to kill 1422: No such process
fuse: failed to access mountpoint /etc/pve: Transport endpoint is not connected
[main] crit: fuse_mount error: Transport endpoint is not connected
[main] notice: exit proxmox configuration filesystem (-1)
 (warning).
invoke-rc.d: initscript pve-cluster, action "restart" failed.
dpkg: error processing pve-cluster (--configure):
 subprocess installed post-installation script returned error exit status 255
dpkg: dependency problems prevent configuration of libpve-access-control:
 libpve-access-control depends on pve-cluster; however:
  Package pve-cluster is not configured yet.
dpkg: error processing libpve-access-control (--configure):
 dependency problems - leaving unconfigured
Errors were encountered while processing:
 pve-cluster
 libpve-access-control
                                         
Current status: 1 update [-59].

I should have not tried to upgrade pve-cluster .
 
You must log in or register to reply here.
Top Bottom