Hi,
I'm having trouble with a new setup.
I have setup the ZFS pool manually as there a parameters outside of the GUI I wanted to set, mounted the pool and make sure the owner is backup:backup.
However everytime I run the backup regardless of VM or backup job I get the same error.
"backup...
Hi Everyone,
I'm having some trouble with getting IOMMU to work. I want to pass through Intel UHD using GVT-g. I might be guess that the CPU doesn't support SR-IOV (Might Intel 8th i7 did....) . I have VTD-D enabled in the BIOS.
However when I click on the Device list, its completly empty...
Hi,
We are running Proxmox 6.3-x and trying to upgrade the firmware on our Intel SSDs.
We have installed the latest version of Intel MAS and can see the firmware updates are available but there appears to be something locking the disk that prevents the upgrade.
[root@proxmox1]:~# intelmas...
Hi,
Firstly I would like to say thank you to the Proxmox team for creating this product. PBS has addressed one the major areas I thought was missing in Proxmox (incremental backups, replication) and presented challenges for us to grow on PVE and PBS has address this.
I have a few questions...
Sorry for the post, I found the answer
qm delsnapshot 130 prerestart --force
qm delsnapshot 130 aftermanualcheck --force
qm delsnapshot 130 aftermanualwork --force
qm delsnapshot 130 premigration --force
Hi,
We had a small outage due to a OSD becoming full on CEPH. At the time this was during a clone of a VM.
This particular VM had a series of snapshots that I am trying to delete but when issue the delete command I get the error:
TASK ERROR: VM 130 qmp command...
I think the upgrades might have triggered some unstable state on the Arista switch side. MLAG and LACP appears to have stabilized now.
After rebooting each switch in sequence it seems traffic has been restored.
I have now upgraded all 4 nodes back to 6.2-12 and it appears to be functioning...
I downgraded all host but still experincing the same affect.
On the switch side I can see the MLAG states flapping
local/remote
mlag desc state local...
Hi MrXermon, Thanks for the response. Our environment is IPv4 only. Good to know about the SNMP as well thank you for the clarification.
I also should note that when I migrate a VM I can see this in the output now after upgrading
tput: No value for $TERM and no -T specified
tput: No value for...
Single host update that is hosting all the VMs
#roll back to a single host
apt install pve-firewall:amd64=4.1-2
apt install pve-manager:amd64=6.2-11
apt install pve-kernel-helper:amd64=6.2-6
After downgrading I have reset the host.
Pings will work temporary to a routed IP but then will...
Small update from my last post. Rolling back ifupdown2 to the previous version had no improvement.
apt-get install ifupdown2=3.0.0-1+pve2
I get about 10 packets in before the packet lose sets in.
I should also note on the switch side I can see some interfaces intermittently falling out of lacp.
TAT41-SWL04#show etherchannel
Port Channel Port-Channel1:
Active Ports: Ethernet2 PeerEthernet1 Ethernet1
Configured, but inactive ports:
Port Reason unconfigured...
Hi,
We have a 4 Node cluster running CEPH and consistently upgraded for over a 1 year.
However after the nodes restarted for the new round of updates last night we found our VMs have intermittment packet lose.
In the kernel logs we are seeing STP events and packets received with its own...
ok, so I got jumbo frames working now and the lacp fast but just wanted to make sure its okay to configure as below.
auto bond0
iface bond0 inet manual
bond-slaves eno1 enp3s0f0
bond-miimon 100
bond-mode 802.3ad
bond-xmit-hash-policy layer2+3
bond-lacp-rate 1
#Data Network...
Hi,
I am getting started with proxmox so apologies in advanced for the basic questions but was wondering if someone could help guide me in the right direction.
How can I enable lacp-fast
How can I enabled jumbo frames (various post show different methods)
e.g. pre-up ip link set eth0 mtu...
Hi,
We are testing Proxmox with 3x Node cluster. Configuration is:
3x Nodes with 64gb each
2tb NVMe x2 p/node for OSD in CEPH
Dedicated 10GbE uplink for storage
1x 10tb SATA HDD 7200rpm connected to one host and exported to all as NFS over 10GbE.
Version: 5.2-10
So far the cluster has...
Hi, quick question. I am going to start evaluating Proxmox and I am just wondering what is the max support size of a VM in a proxmox 5.3 cluster?
e.g.
Max Supported Memory Size of a VM?
Max supported CPU Sockets of a VM?
Max Supported vdisk size on CEPH RBD?
Max Supported vdisk size on NFS...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.