I've followed the steps in the wiki and ensured my switch has multi-cast enabled but cannot add my replaced node back into my cluster. I get hung up at "Waiting for Quorum" Here's the output from new replacement node:
root@proxmox03:~# pvecm add X.X.X.X
The authenticity of host 'X.X.X.X...
I followed the wiki article and modified the IPMI config file with the information for all 4 of our servers (SuperMicro Twin2 box with 4 servers inside 2U) and the verification worked for my config here:
ccs_config_validate -v -f /etc/pve/cluster.conf.new
Creating temporary file...
I'm setting up a new cluster using a 2 Twin2 from SuperMicro. I have the cluster setup and everything looks good however when I migrate a Centos VM I see this:
TASK ERROR: command '/bin/nc -l -p 5900 -w 10 -c '/usr/bin/ssh -T -o BatchMode=yes X.X.X.X /usr/sbin/qm vncproxy 100 2>/dev/null''...
I'm trying to setup a PFSense KVM as my router, but my datacenter forces all connections to 10bt full duplex. I've tried manually setting the speed inside PFSense itself, but it keeps defaulting to 1000bt which is causing a lot of traffic issues.
Is there a way I can set vmbr1 to 10bt full...
I finally got around to updating to the newest kernel this morning and have a few OpenVZ VM's I would like to get rid of. I cannot delete them from PVE's webadmin, how do I do this manually?
We're having some performance issues with our PVE setup lately, specifically I/O spikes, and I see tons of these entries in the syslog. What is going on with all these child processes starting?
May 25 07:21:07 proxwww 28335 Starting new child 28335
May 25 07:21:30 proxwww 28358 Starting...
This is strange. I have 3 CentOS 5.4 KVM's that were switched from RTL8129 to e1000 nics. Now at boot all 3 of them have inactive ethernet ports and have to be activated manually. I've checked their settings on all 3 of them and the prefs (within CentOS) say that the ethernet port will be...
Just out of curiosity, what is the best configuration for CentOS based VM's? I have 4 of them on my server with 8xsata drives in RAID10 and performance of them is not very good at times. CPU utilization is very low as is ram usage, but disk usage is very high as each server writes thousands of...
This is strange. I cannot log into my PVE 1.4 setup via web admin. I put the username and password into the fields and it just sits there until I get a username/password error message. I know my login works as I can log in with SSH.
I'm experimenting with a Kerio MailServer KVM and trying to move it to an OpenVZ CentOS container. The question I have is regarding paths and *where* the data is going. If I'm in my OpenVZ container I've given 300GB of space to, I type df and get
simfs / 10%
none /dev
The path for the...
I'm about to try and get the 3Ware web admin installed and wondered if anybody ran into problems getting it to come up? I've got the cli installed, but it seems I can't configure email notifications from the cli.
I've got a KVM setup with 1GB of ram I want to increase to 2GB. I shut down the vm and changed the memory in the webpage, but when it boots up it only has 1GB of memory.
Should this be possible to change how I describe it?
I have a 8x2TB raid 10 volume on a 3ware 9650SE8-LP. I used the 3ware setup to partition 50GB before the 2TB raid slicing and installed Proxmox. Upon reboot I get "Loading Stage 1.5" repeating over and over again. XenServer installed just fine with the same partitioning.
Do I need to make...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.